with proper value

Q: Applying finger pressure on the belt near the pulley end is the correct method to check the tension…

A: True

Q: The strength of solid shaft is of hollow shaft of same weight. the strength

A: The torque transmitted by the hollow shaft is more than a solid shaft for the same weight and…

Q: Discuss proper handling of the centrifuge.?

A: The centrifuge is a device that is used to rotate the samples at and very high speed. Centrifuge is…

Q: Q2.Write Types of Key and Explain in detail with Diagram.

A: key A key is a machine element which is used in between shaft and hub or Boss of the pulley to…

Q: What are the four movement that to be checked in a propeller loose blade

A: given; What are the four movement that to be checked in a propeller loose blade.

Q: For the shallow shaft, the inside diameter, d is generally expressed in terms of the outside…

A: To Find :The diameter d is generally expressed in terms of the outside diameter.Given : The inside…

Q: Mention the scientific term for "the ratio of density of a given solid or liquid substance to the…

A: This question is based on the concept of fluid mechanics.

Q: Steps in the procedure of measuring the volume of liquid using a graduated cylinder.

A:

Q: differentiate between shaper and planer machine any six difference

A: A shaper is a reciprocating type machine used to produce horizontal, vertical, and inclined surfaces…

Q: Lathe Machine tool is an example of three axes machines

A: Lathes, by definition, are 2-axis machines. Once machines advanced to incorporate 3-axis, 4-axis…

Q: Technician A says that a micrometer can be used tomeasure the outside diameter of something.…

A: Micrometers exist in a variety of forms, depending on what they're used for. An exterior…

Q: the force needed to deflect 1 inch of length is called

A: The force needed to deflect one inch of length can be called as stiffness.

Q: During drilling operation, work piece must be held in vice. Select one: True False

A: Given Statement : During drilling operation, work piece must be held in vice. Select one: True…

Q: Hot hardness means that the material will lose its hardness at high temperature. True or false and…

A: The hardness of a material is associated with the strength of the material. This is associated with…

Q: which value could be most damaged when used for throttling purposes

A: what could be the most damaged valve for throttling purposes

Q: Adding chromium to steel will move the critical points towards

A: The critical point is defined as a point where one phase transforms into another phase. For example,…

Q: If a force doubled, impulse will triple. True or false

A:

Q: Define and explain hookes law

A:

Q: True or False: The BREAK command requires two separate points when breaking a circle.

A: The BREAK command is used to break the selected object between two points.

Q: Lathe Machine tool is an example of three axes machines Select one: True False

A: The lathe machine tool axis - The cross slide (or turret) motion at a right angle to the spindle is…

Q: The simplest type of balance for weighing is the___________.

A: To balance the weight, there are multiple possible lever arrangement. One such example is shown…

Q: голь 40° Find P. do, 25°

A:

Q: True or False? The largest diameter threaded rod is available only up-to 8-inches

A: The threaded rod has several different measurements associated with it. There is major diameter,…

Q: why12ft was not used?

A: We know that the moment is calculated with respect to the position vector of point of application of…

Q: Identify the part not belonging to micrometer. Ratchet Clamp O Locknut Frame

A: Given :-  Identity the part not belongung to micrometer Ratchet  Clamp  Locknut Frame

Q: Draw three views of the adjusting bracket. . Orill-2 Holes 3 BOrill

A: The figure below shows the top and front view of the given model.

Q: The deep drawing blankholder is used in order to avoid defects of the flange which are named O a.…

A: b. The deep drawing blank holder is used to avoid wrinkling defect

Q: List some factors of safety for design of drilled shafts.

A: A drilled shaft is a deep foundation that is constructed by placing fluid concrete in a drilled…

Q: The BREAK command: a. Will work on lines and arcs b. Will work on closed objects c. Can have the…

A: BREAK Command is a tool in AutoCAD software which is used for removing part of an object, open or…

Q: A.What is propeller shaft B. Function of propeller shaft C.how to repare the propeller shaft D.…

A: A. propeller shaft is used to transmit energy of rotation from the engine to the wheel/rotor. In…

Q: Steps how to draw a needle of a cannula using SOLIDWORK

A: Dassault Systèmes' SolidWorks is a solid modelling computer-aided design and computer-aided…

Q: hat is the increment of the 3 cylinders?

A: When we increase the number of cylinders in a vehicle, the power and performance of the engine both…

Q: The guide for the width of the key is O 1/4 of shaft diameter O 1/3 of shaft diameter 3/4 of shaft…

A:

Q: Lathe Machine tool is an example of two axes machines Select one: True False

A: Solution:

Q: While Drilling it is permissible to leave the check key in check while drilling a hole.

A: While Drilling it is permissible to leave the check key in check while drilling a hole. Answer:…

Q: What is meant when a metal is said to have goodweldability?

A: Weldability describes the ease with which a metal can be welded properly. The weldability of any…

Q: List three rules to follow when using or storing semi-precision measuring tools.

A: Semi precision tools are used for the measurement of the various dimensions of the workpiece.

Q: What was the orginal size of the smallest outside diameter?

A: Data given-

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.