With neat sketches explain the hydraulic quick return mechanism used on a shaper?

Q: If you have a steel, through-hardened gear with a HB of 250, factor of safety of 1.2, at room temp,…

A: Given, Brinell hardness number,BHN=250Factor of safety, N=1.2 From the steel hardness conversion…

Q: 3 50mm link is fixed, the number of finks can rotate fuy filly that

A: Given data: Let 4 links;s=100 mmp=200mmq=300mml=350mmas shown in fig. if 350 mm is fixed  then  no.…

Q: how to design shaft based on critical speed for agitator?

A: Design of shaft for agitator:- .Tip speed- it is defined by speed of the agitator's blade tip or…

Q: A cast-iron gear with 100-mm effective diameter and t = 40-mm hub engagemen length is to transmit a…

A: Given: R - 10 mm t - 40 mm T - 120 N.m ro - 50 mm Ec - 100 Gpa Es - 200 Gpa f - 0.16  v - 0.3 To…

Q: Q4. If you have a rod with an initial diameter 12 mm, final diameter is 10 mm and yield stress…

A: Given: The initial diameter of the rod, di = 12 mm The final diameter of the rod, df = 10 mm The…

Q: With neat sketch explain the crank and slotted mechanism?

A: The crank and slotted lever mechanism is a quick return mechanism in which forward strokes are…

Q: 6. The steel shaft shown rotates at 3 rev/sec with 30 kW removed at A, 15 kW taken off at B, and 45…

A:

Q: Use table AT-7 , Faires A 5000-lb. gear box is provided with a steel (as rolled B1113) eyebolt for…

A:

Q: Draw the assembly views of the following G Clamp from a front view and top view. Provide a standard…

A: To Draw the assembly views of the following G Clamp from a front view and top view.

Q: What is nutation in gyroscopic motion?

A: Nutation: The nutation word is taken from a Latin word ‘nutatio’ which means swaying or nodding. It…

Q: Describe the noncircular shafts?

A: The non-circular shafts are ones that do not have a circular profile and the shear stress for the…

Q: 4) A kiln is driven by a bull gear and pinion arrangement. There are 250 teeth on the bull gear. The…

A: To find: The speed of the motor. Given: The number of teeth on bull gear is Tb=250. The number of…

Q: Make the definition of Spring Pin and what are the advantages and disadvantages

A: Spring Pin: It is an mechanical fastener. Spring pin is used to tight the relative positon of  two…

Q: 7. A typical drive train for a 'geared' bicycle meant to be used on paved road (see a representative…

A: (a) Write the given data. Tf=48Df=10.5 inTs1=30Ts2=26Ts3=23Ts4=20Ts5=16Ts6=12Nf=105 rpmFf=28 lb

Q: what is the equation of the addendum and dedendum in bevel gear

A: Equation for addendum is ab=1Pwhereab=addendum of bevel gearP=Diametral pitch

Q: A tripod plotted in a 3-D coordinate system is supporting a downward vertical load of P = 443 kN at…

A:

Q: 2. Calculate the volume of hexagonal head bolt by measured data at Instruction 1.

A: GivenPart A(tail part).Volume=π4c2DVolume=π4×15.582×40.11Volume=7642.8mm3Part B(Head…

Q: To determine the velocity of slotted slider for different crank lengths at different crank angles…

A: Step 1 : let the crank length is 40 mm The crank angle is 240° The angular velocity is 1.5 rad/s The…

Q: 6. The steel shaft shown rotates at 3 rev/sec with 30 kW removed at A, 15 kW taken off at B, and 45…

A:

Q: Describe tapper noise

A: Ther is a concept called tappet noise When the engine is running ideally there comes a regular…

Q: State advantages of Cycloidal & Involute profile as a gear tooth profile ?

A:

Q: Rotary crusher work better on materials Brittle and hard Soft and plastic O The two types O

A: Rotary crusher are generally used to crush brittle and hard materials. They are used in mines.

Q: cycloidal g

A: The cycloidal gear profile, as opposed to the involute gear profile used in most other gears, is a…

Q: pur gear

A: GIVEN: What is spur gear?

Q: its of cycloid g

A: The cycloidal gear profile, as opposed to the involute gear profile used in most other gears, is a…

Q: What are the TPI and TPF of a part with end diameters of 3/4" and 1/2" and a taper length of 4.25"?

A: A cylindrical taper is a piece of material that decreases in diameter in a cone shape. Proportions…

Q: 1 Problem 9.19 Determine the equivalent state of stress on an element at the same point which…

A: Here, Plane stress condition is given, we can solve this problem by analytical as well as by Mohr's…

Q: Using part reduction method redesign gear pump and calculate the assembly time using…

A: Machine Design :- Machine is a combination of linkages having definite motion and capable of…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.