With a D'Arsonval movement with 100 internal resistance and 1 mA FSD current, it is required to design a multi- range voltmeter with a voltage ranges of 10 V, 50 V, 250 V and 500 V by using a multipliers all connected in series with the moving coil. Therefore Rs1=........... Rs2=........., Rs3=............ Rs4=......... O O O R_s1= 9.9 KQ, R_s2= 40 KQ, R_s3= 200 ΚΩ R_s4= 250 ΚΩ R_s1= 9.9 KQ, R_s2= 40 KQ, R_s3= 20 KQ R_s4= 250 KQ R_s1= 99 KQ, R_s2= 40 KQ, R_s3= 200 KQ R_s4= 250 KQ R_s1= 9.9 KQ, R_s2= 400 KQ, R_s3= 200 ΚΩ R_s4= 250 ΚΩ

Q: c) The shown converter in Figure 1 operates in continuous conduction mode. Assume the components are…

A: Given: The circuit shown below operates in the continuous conduction mode: To find: (i) Sketch…

Q: b) A six-phase half-wave rectifier is fed from a 3-phase, 440 V, 50 Hz ac supply and it is connected…

A: To analyze the six-phase half-wave rectifier, let's start by determining the output voltage and…

Q: Define and describe the various circuit stages required to design a DC power supply (specifically,…

A: According to the question, we need to describe the DC power supply circuit as shown below

Q: A full wave and a half wave rectifier with identical components and load, are fed from a sinusoidal…

A:

Q: My circuit is a Wall-Wall rectifier circuit. The transformer is taking in 120Vac from the wall and…

A: We can draw the above circuit as   here peak value of secondary voltage will be…

Q: Q2\ fill in the blanks. 1- There are three types of thermistor ..... and

A: Since you have posted multiple questions, we will provide the solution only to the first question as…

Q: For a full-wave peak rectifier circuit shown below, prove the following: Vr = Vp 2fCR id,avg = I₁…

A: According to the question, for the given circuit as shown below We need to prove the following,

Q: 12. The resistance of an NTC thermistor as measured temperature (a) decreases .... increases (c)…

A: Thermistor is a type of resistor which is strongly dependent on temperature. NTC thermistor-…

Q: A basic d'Arsonval movement with Rm= 100 n, and Ifsd= 1 mA, is to be converted into an ac voltmeter…

A: Given circuit is half wave rectifier Im=1 mA    =1×10-3ARm=100Ω

Q: Q2. A full-wave controlled rectifier circuit with resistive load shown below: Calculate the firing…

A: Given that  A full-wave controlled rectifier circuit with resistive load shown below: Calculate the…

Q: A half-wave rectifier is needed to supply 15 VDC to a load that draws an average current of 250 mA.…

A: I hope this is helpful If you have any doubt you can ask me

Q: The three-phase diode rectifier is fed from an AC source of 230 V, 60 Hz. The load is designed with…

A:

Q: You are an electrician working on an overhead crane. The crane uses a large electromagnet to pick up…

A:

Q: Determine the percentage increase in DC voltage if a full wave rectifier uses a 10mF capacitor. The…

A:

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.