Wind blows on the side of the fully enclosed warehouse building as shown which is located on open flat terrain in Bacoor City, Cavite. If the building is classified as Category 5 and under Exposure C with a wind speed of 230 kph, determine the design wind pressures on all sides of the building and on the roof of the building. 02. 10 m 30 m 15 m wind D.

Wind blows on the side of the fully enclosed warehouse building as shown which is located on open flat terrain in Bacoor City, Cavite. If the building is classified as Category 5 and under Exposure C with a wind speed of 230 kph, determine the design wind pressures on all sides of the building and on the roof of the building. 02. 10 m 30 m 15 m wind D.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The unheated storage facility is located on flat open terrain near Sicilia Island, Italy. Determine the design snow load on the roof. How about if the slope of the roof is 45° ?
(1) Figure 1 shows a two-story one-by building. The structural story stiffness are kı-k₂-1x106 N/m, the floor masses are m₁= m2-1000 kg, the story height is 3 m both stories. This building located in a zone of site category of II, and the damping ratio of the two modes are all 0.05, the fortification intensity is 7 (basis acceleration value equals to 0.15g), belongs to the 2nd group. Answer the following questions. (a) Use the modal decomposition-based method to carry out the structural design. Please calculate the designed base shear and the inter-story drift ratio of the 1st story. The circular frequencies and mode shape vectors of the structure are given as following, (The corresponding tables from the Seismic Design Code is given in the Appendix) (b) Use the modal effective mass to explain why the design base shear of structure is dominated the 1st modal response. W₁ = 6.8 rad/sec; w₂ = 17.7rad/sec = {-1.618 Φι = {0.618; 2 = { = 992 195.2 üz k2,c2 (2) For the same structure shown…
Theory of Structures
The precast floor system consists of a 150-mm-thick concrete slab carry its self weight as well a Live Load of (2 kNm) is simply supported on three concrete beams of dimensions (300*500)mm that, in turn, are supported by two concrete girders of (300*600mm), (each girder is support on two columns) as shown in Fig.1. Determine the loads acting on beams BE and AD and girder AC. (concrete density: Let Yoncrete 24 kNm') Concrete Girder (300*600mm 10 m 5m Concrete floor beam (300 500mm 5 m Fig. (1)
The second floor of a light manufacturing building is constructed from a 125 mm thick stone concrete slab with an added 100 mm cinder concrete as shown. If the suspended ceiling of the first floor consists of metal lath and gypsum plaster, determine the dead load for design in kN per square meter of the floor area. 125 mm concrete slab ceiling 100 mm cinder concrete ANS. 5.055 kN/m²
P2.15) Determine the dead load and live load for the second floor of a library in which any area can be used for stacks. Assume that there will be a steel channel ceiling system (2 psf) and asphalt tile on the floors. The floors are 6-in. reinforced concrete. Allowance should be provided for mechanical ducts.
Question 5 The plan dimensions of a public hall in a village measures 8.5 m * 20 m. The roof of the building is mono pitched where the low eave height is 3 m and the high eave height is 4.5m. If wind direction is considered at 180', determine the net effect of external and internal pressure coefficients for the zones of mono pitched roof. Openings in windward side: three windows of dimension: 2 m * 2 m. Openings in leeward side: two doors of dimension: 2.5 m * 2 m. Openings in wind parallel sides: one window, in each side, of dimension: 2 m * 1.5 m.
19. A building roof contains 15000 square foots, of horizontal project area. If design is based on a (4 in /hr) rainfall intensity. How many (6 in ) diameter roof drain would be required? One Leader O Two Leader O Three Leader O No Leader
Consider a composite wall that includes an 8-mm-thick hardwood siding, 40-mm by 90-mm hardwood studs on 0.65-m centers with glass fiber insulation (paper faced, 28 kg/m³), and a 12-mm layer of gypsum (vermiculite) wall board. What is the thermal resistance associated with a wall that is 2.5 m high by 6.5 m wide (having 10 studs, each 2.5 m high)? Assume surfaces normal to the x-direction are isothermal. Rtot = P K/W Wood siding Stud Insulation Wall board