Why must the loading not significantly change the original geometry orconfiguration of the member?

Q: What happens when the principal stresses act on the element?

A: In this problem, a shaft with moment and torque applied at the free end and one is fixed. And, here…

Q: What would the minimum static factor of safety be based on yielding?

A:

Q: How can we determine the deformation of an axially loaded member?

A: Whenever a member is loaded axially there is change in the dimensions of the member. Length of the…

Q: Which of the followings is a factor that reduces the fatigue life of the component: O Shot peening…

A: 1. Shot peeing is the process to improve the fatigue strength. 2. By cold rolling the fatigue…

Q: Why should the selected section modulus, be slightly greater than Sreq>d?

A: Generally, section modulus is calculated by considering external loads only. So in order to account…

Q: What is the effect of an eccentric loading?

A: Eccentric loading: The eccentric loading is a type of loading on beams and columns in which load…

Q: Describe the State of Stress caused by the combined loadings?

A: Combined loading: In combined loading conditions,  the specimen/ component is subjected to various…

Q: What are ratchet lines, and how are they arranged with respect to the fatigue crack front and any…

A: Ratchet lines are steps in fatigue fracture surfaces  that originate  from the interaction between…

Q: Describe the shear-flow distribution throughout a member's cross-sectional area?

A: The shear flow distribution is the distribution of shear stress over a distance or cross-sectional…

Q: Which choice below describes the mechanical property materials called toughness a ability to…

A: Which choice below describes the mechanical property materials called toughness a ) ability to…

Q: Why is it necessary to be sure the actual bending and shear stress in thebeam does not exceed…

A: The actual bending and shear stress:  The actual bending stress and shear stress of a beam should…

Q: To eliminate distortion while achieving a uniform structure and response to heat treating…

A: Given: To eliminate distortion while achieving a uniform structure and response to heat treating…

Q: What is the Constant Load and Cross-Sectional Area?

A: Load: The load is a force that caused the stresses, deformation, and acceleration in the bodies.…

Q: What cross-sectional property is influenced by the size effect factor between the depth and width of…

A: The properties that get affected by the depth and the width of the member are given below: (A) The…

Q: What are some materials (high alloy casted) that have excellent wear resistance and weldability with…

A: This question is based on the concept of excellent wear resistance and weldability of materials.

Q: How did temperature affect the toughness of C1045-CF, Cast Iron, and AL7075-T6

A: Ductility: The property of a metal by virtue if which it can be transformed into thin wires by the…

Q: Discuss the effects of applying a torsional loading to a long straight member?

A: Torsional Loading causes the deformation of the straight member about its longitudinal axis. It is…

Q: How can the fatigue be prevented?

A: Fatigue: Fatigue is the deformation material due to cyclic loads applied to it. This results in the…

Q: What is the tension and compression test?

A: Tension and compression test are preferred for determining material properties like elastic limit,…

Q: By what means kind of small area or stripe be selectively hardened and a large steel pa

A: induction hardening and flame hardening

Q: When does the Fatigue occur in the material?

A: When a material is subjected to repeated or cyclic loading then the failure in the material is…

Q: On what is the Design of a member for strength-based?

A: The strength-based design approach is a type of design where our main focus is on strength of…

Q: I need answers to parts 7, 8, and 9, pertaining to the print provided.

A: At what scale was the original drawing created?

Q: When does the impact occur?

A: Impact: It the force that is applied to the specimen or object from a certain height. These are…

Q: What makes stainless steel corrosion resistant?

A: It is well known that stainless steel is the iron-based alloy. It is used in making many components…

Q: Which metal often does not have a well-defined yield point and which procedure is suitable to yield…

A: Answer : Yield point : It is defined as that point after which material does not regain its original…

Q: What role can a notch or a flaw play in determining the total fatigue life of a component?

A: Fatigue Life of a component: The number of cycles of stress-strain which a specimen can withstand…

Q: What material and corresponding stresses is best for HP shape?

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.