why is it important to vent each bulb in two bulb mēthod to the atmosphere before determuning D (diffusion coeficient) and Amixs?

Q: 4. Solve the value of P based on tension on the net area. а. 663.66 kN с. 823.32 kN b. 756.00 kN d.…

A:

Q: (a) Explain the principle of refrigeration system and its components in not less than 200 words.

A: The refrigeration principle and components of system

Q: 3 Hydraulic motors which operate in both directions are commonly A) Used in conjunction with a…

A: Given question is based on hydraulic and state of air.

Q: Steam is used in an ideal combined reheat and regenerative system as shown in figure A (turbine and…

A:

Q: Gear 2 (pinion) runs at 1800 rpm ccw and transmits 3.5 kW to frictionless, idler gear 3. The…

A: Given:- P=3.5kW m=2mm Pressure angle=20° N=1800rpm To find:- g) Torque on gear 4

Q: 5) 1000 kg of potatoes are processed to obtain french fries. Raw potatoes are washed, peeled, cut…

A: Given: (a) The french fries are made from potatoes which can be shown by following flow chart.

Q: For number 1 and 2. Use the method of joints to determine the force in each member of the roof truss…

A: As per Bartleby's policy, I can answer only the first question. please resubmit the second question…

Q: 1 -1 Given the matrices A= 2. 2 1) B = 1. Show that (A+B) + A² +2.AB + B² .

A: Since we only answer one question at a time, we will answer the first one. Please resubmit the…

Q: 4. Two and one-half pounds of air actuate a cycle composed of the following processes: polytropic…

A:

Q: L 32 mm L Cross-section K, aran : 17 nam + 6 E= 200 kN/mm m = 15 kg KI= lo kN/m Find f

A:

Q: Consider a Carnot vapor refrigeration cycle with Refrigerant 134a as the working fluid. The cycle…

A: Given:Cold region temperature, TC=40oFThe ambinet temperature, TH=90oFFind:Coefficient of…

Q: Explain the Beam radiation and diffusive radiation with necessary diagram.

A: Solution (1): The beam radiation and the diffuse radiation are the components of solar radiation.…

Q: Answer D

A:

Q: Instructions: Identify the talking components by choosing the most appropriate answer from the…

A: To determine: I directly determine what the speed of a hydraulic actuator is going to be. What am…

Q: Determine P and RA

A:

Q: (-3+ ]32–1 )wnt (-3- [32-1 )wnt X = A e +Be With initial conditions x(0) and x( 0), we found: =…

A:

Q: A 1000 kg automobile accelerates from 10 km/hr to 120 km/hr. How much work does this require?

A: Question(4)Given:Mass  Initial Velocity Final Velocity To find:The required Work

Q: 1. on-off: 2-way/pressurize-exhaust: 2. pneumatic valve: sub-base mounting/hydraulic valve: 3. hand…

A: Here in this question we have to complete the suggested relationship by choosing the appropriate…

Q: 3. A juice at a rate of 500 kg/h is heated from 60 °C to 115 °C. The juice has a specific heat of…

A: To Find :  The mass flow rate of steam necessary to heat the juice. Given :  The mass flow rate of…

Q: Lukewarm water at 60 °C in a storage tank is being pumped at 300 L/min from the tank. The line from…

A: Water temperature, T=60oCWater flow rate, Q=300 L/min=300*10-360m3/s=0.005 m3/sLength of suction…

Q: Mechatronics Write the Boolean Expression for each of the following Figures: 1. 2. Page | 2

A: 1) A*B, since it is a AND gate

Q: PROVE THAT THE ANGLE IS 30° BY LAWS OF CONGRUENCY

A:

Q: Instructions: In this exercise, incomplete relationships are set up among fluid conductors and…

A: Here, we have to complete the relationship among fluid conductors and connectors by choosing…

Q: 1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28…

A:

Q: A stick of butter at 35°F measures 1.25 in. x 1.25 in. x 4.65 in. and weighs 4.2 ounces. Find its…

A: (1) According to the given data Volume=1.25inx1.25inx4.65inweight=4.2 ounces=0.2625lb   {…

Q: 8.9 Design a mechanical system which can be used to: (a) operate a sequence of microswitches in a…

A: (a) Mechanical system used to operates a sequence of microswitches in a timed sequence is Camshaft.…

Q: O. No. 1: A rectangular beam with cross-sectional dimensions b-40 mm and h- 55 mm is subjected to a…

A: As per bartleby guidelines i can solve only one question at one time. kindly upload second question…

Q: G₁ Go CODOVODS G₂ G₁ G

A:

Q: Rigid rods of negligible mass lying along the y axis connect three particles (Fig. P10.25). The…

A:

Q: A piston/cylinder system filled with water at 70°C has a radius of 0.5 m and an initial piston…

A:

Q: 5) Based upon data given in Fig. 2, the primary shear stress generated in the eccentric loaded weld:…

A:

Q: Each line of the following table gives data, in Btu, for a process of a closed system. Determine the…

A: Process (a) Applying 1st Law of thermodynamics Q=∆E+W40=15+WW=25 now, E2-E1=∆EE2-15=15E2=30…

Q: For the stop bracket seen below determine the center of gravity (xbar, ybar, and zbar) A = 12 B =…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.