Why is it better to use an automatic system rather than a manual one?

Q: While discussing secondary voltage: Technician A says that the normal required secondary voltage is…

A: Solution:

Q: A) Using electro-pneumatic  control method Draw the circuit of operation  (the pneumatic circuit and…

A: electro-pneumatic  control method Draw the circuit of operation  (the pneumatic circuit and…

Q: What can be manipulated in order to control the speed of work in a pneumatic actuator?

A: The energy of compressed air or gas is transformed into a mechanical motion by pneumatic…

Q: Technician A says that some systems use a special modulated shift control solenoid. Technician B…

A: In automobile the transmission system uses shift control solenoid which shift the gear…

Q: advantages of using electronic controls rather than relying on conventional hydraulic controls in a…

A: In modern vehicles mostly electronic controls are used rather than the conventional hydraulic…

Q: bull engine is the inversion which type of mechanism?

A: The bull engine is the fourth inversion of the slider-crank chain. In this type of inversion fourth…

Q: What is the difference between Momentary Contact and Maintained Contact?

A: Maintained Contact means that when you push it on it stays on until you push it off and so on.

Q: The O a. cgs system is used widely by chemist and physic

A: Explanation  The most widely used unit in the world by chemist and physicist is SI unit.

Q: Technician A says that throttle position is an important input in most electronic shift control…

A: In electronically controlled automatic transmission, the most appropriate gear ratio for the power…

Q: What rating is used for hearing protection devices? Noise reduction rating O Canister Color Code…

A: Hearing protection devices are used to protect the ears from the noises generated due to the working…

Q: Example: Let us verify the controllability and observability of a control system which is…

A:

Q: How do the different controllers help in operation?

A: In control systems, controllers are tools or algorithms that manage and control how a system or…

Q: Name three types of automatic controls.

A: Given Data : Automatic controls

Q: What is the primary difference between an automatic traction control system and a stability control…

A: Traction control  system in an automobile is designed to prevent the driving wheel from loosing the…

Q: 1. The motor at B winds up the cord attached to the 65 lb crate with a constant speed. Determine the…

A: Given data  given pulley system.

Q: Q1 (a) Figure Q1(a) shows a gear system. Find (i) The relationship between the number of the gear…

A: Solution:

Q: Explain the trip and drive cycle in an OBD II system.

A: On-board diagnostics (OBD) is an automotive term referring to a vehicle's self-diagnostic and…

Q: differentiate b/w overdamped, under damped , criticaly damped, undAmped system

A: The decay of oscillations in a system following a disturbance is described by the dimensionless…

Q: pls do make an ntroduction about  Automatic Return of a Double  Acting Cylinder using Roller Lever…

A: DOUBLE ACTING CYLINDER A double acting cylinder is a chamber wherein the functioning liquid…

Q: If we wish to regulate a bathroom shower temperature, where the input to the system is the ratio of…

A: To determine the controllers which is the most suitable to regulate a bathroom shower temperature…

Q: How can shift feel be controlled?

A: For many years, accumulators and associated circuits have been the dominant way for regulating…

Q: introduction about Control of Single and Double Acting Cylinder

A: A single-acting cylinder in a reciprocating engine is one in which the working fluid only…

Q: How are mechanical cooling system clutch fans often engaged? Select one: a. A ratcheting mechanism…

A: Whereas numerous unused vehicles utilize electric cooling fans, numerous more seasoned vehicles…

Q: Technician A says that a faulty radiator fan relay can cause an engine to overheat. Technician B…

A: The radiator in an automobile is used to take away the excess heat of the engine and sending it out…

Q: The clamping of a work piece is to be controlled by either of two Push buttons. A further push…

A:

Q: Explain the procedures for assessing the starting system and its components of an automobile.…

A: The starting system of car is used for converting electrical energy from the battery to mechanical…

Q: A hot-wire MAF has low resistance across it when the wire is hot: Technician A says that this…

A: In a fuel injected internal combustion system the mass flow rate of air is determined by a sensor,…

Q: 2. The wire AE is stretched between the corners A and E of a bent plate. Knowing that the tension in…

A: Dear student,                    According to the guidelines I am allowed to answer only three…

Q: How does an automatic washing machine use the mechatronics multilevel control architecture in Level

A: A controller is included in the washing machine, which communicates with the motor. The…

Q: What is the importance of studying how to perform assemble/disassemble manual transmission?

A: Manual transmission is also known as multi-speed transmission which involves in gear change in the…

Q: in V-belt drive, why should the upper wrap angle of the small pulley be checked to make it greater…

A: Belts are used to transmit power as well as torque to the shafts. V-belt is one of the type of belt…

Q: Please provide the answer with a free body diagram and answering formula for this analysis of…

A: Find the equation of motion

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.