Why dynamic viscosity is also termed as absolute viscosity?

Q: Explain Coulomb theory.

A: Coulomb’s theory used to determine the shear strength of the soil. It states that the total lateral…

Q: : Determine the deflection and rotation at the end of the foliowing peam. Use E = 29,000 ksi, lAB =…

A:

Q: At a point in beam, the principal stresses are 100 N/mm² and 50 N/mm². The stress in x-direction is…

A: Given -  The principle stresses are, σ1 = 100 N/mm2 σ2 = 50 N/mm2 The stress in x-direction, σx = 65…

Q: A tensile stress is to be applied along the axis of a cylindrical brass rod that has a diameter of…

A:

Q: 4.5-15 The uniformly loaded beam ABC has simple sup- ports at A and B and an overhang BC (see…

A:

Q: Consider the following beam with overhangs: P A В C L Calculate the deflection at A (the end…

A:

Q: For the punching operation shown in the figure, compute the shear stress in the material if a force…

A:

Q: Explain the physical meaning of the terms absolute pressure and gauge pressure

A: Given data in question  Absolute and guage pressures  To be discussed  Physical meaning of Absolute…

Q: In mechanics of deformable bodies, what is the other name for Elongation? is it strain or…

A: Elongation: The elongation is defined as the measure of deformation when an object is subjected to…

Q: Find the rotation at B for the beam and loading below. The moment diagram for the load P is linear…

A:

Q: A tension member consists of a 50-mm-diameter brass (E = 100 GPa) bar connected to a 32-mm-diameter…

A: Given data : Tensile load (P)=50 KNBrass Diameter of brass (dB)=50 mmLength (LB)=1.5 mModulus of…

Q: For the structure and loading shown below, find the lateral deflection at the top. Use E = 29,000…

A:

Q: O. No 8: The section shown in Figure Q. No.8 is applied by a shear force V 1000 lb acting vertically…

A: Using symmetry, V1=V3 andV2=V4 V=100 lbt= 0.5 inb1= 6 inb2= 4 ind = 8 in

Q: Find the rotation at B for the beam and loading below. The moment diagram for the load P is linear…

A: Given: P=1.9 kips=1900 lb E=29,000 ksi  L=11ft=132 inches a=5 ft=60 inches  I=340 inch4

Q: Given the unit vectors A-ti-2j-tk, B-zi-k. and C-rj-2ak. Determine (a)(A x B) C. (b)(A x B) x (B x…

A:

Q: You are given the structure and loading below. The load w is 2.4 kips/ft. Find the value of downward…

A: Given, E=29,000 Ksiw=2.4 Kips/ftIAB= 103 in4AAB=4.7 in2Diameter of BC =0.5 in Calculating support…

Q: Explain the difference between gauge pressure and absolute pressure

A: gauge pressure = the pressure relative to the atmospheric pressure or the pressure above the…

Q: Q.5) A bar of 20 mm diameter is tested in tension. When a load of 38 kN was applied extension of…

A: Given data : Inital diameter (d)=20 mmLoad (P)=38 KNExtension in length (δL)=0.12 mmLength (L)=200…

Q: The homogeneous rod ABC is supported at point B, and two masses (m1 = m2 = m) are attached at…

A: The given figure is shown below:

Q: Q04 A rod is subjected to an uniaxial load within linear elastic limit. When the change in the…

A:

Q: Discuss the term engineering stress and engineering strain.

A: Engineering Stress:- Stress can be defined as internal resisting force per unit area of the body.…

Q: A rectangular beam 150 mm wide and 200 mm deep, is simply supported on a span of 6 m. Two loads of 5…

A:

Q: (a) Name the non-ferrous metal used to make cooking pots. (b) Name the metal used for plumbing. (c)…

A: Thank you for the question. As per honour code we are allowed to  answer the three subparts at a…

Q: Briefly discuss the difference between Elastic and Plastic behavior of materials?

A: Solution: Solid structures in all engineering fields are subjected to loads that can be either the…

Q: If a point in a strained material is subjected to two mutually perpendicular stresses, σx = 100 MPa…

A: Given data,  σx = 100 MPa (tension)  σy = 50 MPa (compression)

Q: Dimensions

A: To find: Dimensions of kinematic viscosity.

Q: P6.19 A compound shaft drives several pulleys, as shown in Figure P6.19. Segments (1) and (2) of the…

A: Given -

Q: What are the units of Axial Deformation and Axial Strain?

A: This question is related to the Strength of the material from Civil Engineering. It is subjected to…

Q: You are given the truss and loading below. Find the value of downward deflection at point C. Use E =…

A:

Q: A reservoir of glycerin (glyc) has a mass of 1200 kg and a volume of 0.952 m². Find the glycerin's…

A: Mass of glycerin, m=1200 kg.Volume of glycerin, V=0.952 m3.

Q: Solid Mechanics normal stress and it's unit?

A: solution of above problem is below:

Pressure and Stress