Why do you need to determine the support reaction before going to calculate internal member forces of a truss? Select one: a. This reduces the calculation b. This results in reduction on the formulas used c. This procedure is not done at all d. This makes the isolated section more complicated

Why do you need to determine the support reaction before going to calculate internal member forces of a truss? Select one: a. This reduces the calculation b. This results in reduction on the formulas used c. This procedure is not done at all d. This makes the isolated section more complicated

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 4 Analyze the truss and calculate all the forces acting on Joint B and H. Show your detail steps with FBD if necessary. 10% 321 A 24' 12k H B 20 k 24' 8k G 40 k 24' D 40 k 24' E
I-section built-in beam in the figure shows two forces It is in effect. These forces at point A and B stress element by finding the stresses that it generates Please show on. Note: force of 100 kN It is in the x-y plane and the point of action is Take as its surface. Force with a magnitude of 180 kN I is in the center of gravity of the section (Search all show transactions and required reductions
9 in. 30° x 6 in. 3 in. * B 3 in. 3 in. 4 in. The top cylinder weighs 100 lbs., the middle cylinder weighs 150 lbs. and the bottom cylinder weighs 200 lbs. A) Compute the forces on the L shaped support rack from each cylinder. Include free body diagram of each cylinder. B) Compute the reactions on the L shaped support rack at A and B. Include a free body diagram of the support rack.
2: Answer briefly the following: 1- The method of joints is used to analyze and design trusses. This method is based on what? (For section A only) 2- Define Simple Truss. (For evening section only) 3- The method of sections is used to analyze and design trusses. This method is based on which principle? (For section B only)
Please answer both parts.
Short answer please
Need help with these Q2. Identify any zero force members. ( there can be more than one ) Member AB Member AJ Member BCBC Member BH Member BJ Member CD Member CG Member CH Member DE Member DF Member DG Member EF Member FG Member GH Member GJ q3. You are asked to find the forces in members GHGH and CGCG using the Method of Sections. Which members should you make a cut through? Member AB Member AJ Member BC Member BH Member BJ Member CD Member CG Member CH Member DE Member DF Member DG Member EF Member FG Member GH Member GJ Q4. Having made a cut through the members in the previous part, you next want to solve for Member GH. Which of the following equilibrium equations is the most efficient? (i.e. which one will allow you to solve for the required member in one equation?) a. ΣFx=0. b. ΣMC=0. c. ΣMH=0. d. ΣFy=0 e ΣMD=0
PART 1 Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=3.5 m, b=2.0 m, PB = 2 kN, PC = 2 kN, and MB = 20 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. IMAGE* Calculate the reaction forces Ay and MA acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) IMAGE* PART 2 Determine the shear force acting at each of the following locations:(a) x = 0+ m (i.e., just to the right of fixed support A)(b) x = 3.5– m (i.e., just to the left of B)(c) x = 3.5+ m (i.e., just to the right of B)(d) x = 5.5– m (i.e., just to the left of C)When entering your answers, use the shear force sign convention.Answer:(a) V = ? kN.(b) V = ? kN.(c) V = ? kN.(d) V = ? kN. PART 3…
Given the Three - Hinged Arch in a form of Semi - Circle of radius 4 m as shown below. Determine the following: a.) The External Reaction at Point A. b.) The Internal Reaction at Point C. c.) The External Reaction at Point B. 400 N/m 500 N/m r Note: EXPRESS YOUR ANSWER UPTO 3 DECIMAL PLACES.
Question 13 Use the diagram shown above. Given • D₁ = 9 ft D₂=7 ft D₂ 3 D3-4 ft • W = 100 #/ft P = 800 # D. 1 D₂ X W P Solve for the internal moment at X. Note: Enter the numerical value only for your calculation results. You'll be asked to specify the unit for your calculation result in the following question. (This is due to Canvas' lack of ability to require units for calculation question.)