Which one of given below is/are not associated about tool life criteria? Aşağıda verilenlerden hangisi takım ömrü kriterleri ile ilişkili değildir? Workpiece count A) İş parçası sayısı Degradation of surface finish B) Yüzey pürüzlülüğünün bozulması Fracture and temperature failures are premature failures Kırılma ve sıcaklık anzaları erken arızalardır Cumulative cutting time D) Kümülatif kesme süresi

Q: An NDT (non-destructive) examination of a steel component reveals the presence of a 5-mm-long edge…

A: Given : Kic=75 MPam dadN=4×10-37∆K4 Repeated stresses = 400 MPa ao= 5mm

Q: negligible mass. Determine the force (Fin) that the small piston exerts on fluid in small cylinder.…

A:

Q: (a) The mean ultimate tensile strength of a steel is 1500 MPa. What value should be used if the…

A: Note : Since you have asked multiple question, we will solve the first question for you. If you want…

Q: Problem #2: A plate constructed of ASTM A470-8 steel is loaded in tension (P=85 kN) when at room…

A: Given: a = 3 mm b = 35 mm t = 5 mm P = 85 kN ASTM A470-8 properties: Kc = KIc = 60 MPam Yield…

Q: d) Determine the stress, strain and elongation/shortening of member AB (Assume Esteel = 200,000 MPa)

A: Lets the member is A992 steel So, fy = 345 N/mm2 E = 2 x 105 N/mm2

Q: 17.3 A 1-in.-by-4-in. steel bar is subjected to the loads show Calculate the combined stresses at…

A: Given Data -  Cross section of Bar = 1 × 4 inch  Load P1 = 12000 lb . P2 =1200 lb  Find -  Combined…

Q: Two materials with 10 mm² contact area have been tested to determine how much adhesive wear takes…

A: Given:- area = 10mm2 No. of tests = 350 HB277 To find:- average wear coefficient

Q: The Strength Reduction Factor for development length of a rebar per ACI 318-14 is

A: The strength reduction factor for development length of rebar per ACI 318-14 is 0.85

Q: 1. What are the tools and equlpment you need for soldering? 2. What is the temperature of soldering…

A: in this question 12 questions are asked about shouldering.  but as per bartleby guidelines here i am…

Q: ot boon sT Consider an inner beam-column joint in the ground floor roof of a eight storey building…

A:

Q: A 12.5-mm round structural steel rod is loaded in tension to fracture. The 200-mm gage length of…

A: ASKED: To compute the average strain for the steel rod.   Given, Gage length of the rod (L) = 200 mm…

Q: c)How much shorter will the cylinder get under load? d)What is the volume change? e)Supposethere…

A:

Q: Calculate the design (LRFD) block shear rupture strength (k

A:

MATLAB

MATLAB software is a registered trademark, multi-model programming language, and numerical computing environmental system created by MathWorks. 'MATLAB' is the short-form of "Matrix Laboratory". The MATLAB software permits the utilization of matrix operations, graphical representation of data, execution of algorithms, development of user interface, and linking programs created in other languages. Even though MATLAB is developed mainly for numerical computing, there is an optional toolbox that uses a symbolic engine known as MuPAD giving access to all the symbolic computing abilities. In addition to this, a Simulink package delivers graphical multi-domain simulation and design that is model-based for embedded and dynamic systems. MATLAB users are spread worldwide across the world and use MATLAB extensively.