Which of the following would decrease the rate of solvation for solid NaCl in water?The temperature decreases from 500C to 200CA stir bar is added to agitate (mix) the solution.The NaCl is crushed into small pieces using a mortar and pestle.The pressure is increased from 1 atm to 2 atm.

Solvation is the process by which the solvent molecules surrounds the solute molecules and interact…

Which of the following would decrease the rate of solvation for solid NaCl in water? The temperature decreases from 50OC to 200C A stir bar is added to agitate (mix) the solution. The NaCl is crushed into small pieces using a mortar and pestle. The pressure is increased from 1 atm to 2 atm.

Which of the following would decrease the rate of solvation for solid NaCl in water? The temperature decreases from 50OC to 200C A stir bar is added to agitate (mix) the solution. The NaCl is crushed into small pieces using a mortar and pestle. The pressure is increased from 1 atm to 2 atm.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

The small bubbles that form on the bottom of a water pot that is being heated (before boiling) are due to dissolved air coming out of solution. Use Henry’s law and the solubilities given to calculate the total volume of nitrogen and oxygen gas that should bubble out of 1.5 L of water upon warming from 25 °C to 50 °C. Assume that the water is initially saturated with nitrogen and oxygen gas at 25 °C and a total pressure of 1.0 atm. Assume that the gas bubbles out at a temperature of 50 °C. The solubilityof oxygen gas at 50 °C is 27.8 mg/L at an oxygen pressure of 1.00 atm. The solubility of nitrogen gas at 50 °C is 14.6 mg/L at a nitrogen pressure of 1.00 atm. Assume that the air above the water contains an oxygen partial pressure of 0.21 atm and a nitrogen partial pressure of 0.78 atm.
The dispersed phase of a certain colloidal dispersion consistes of spheres of diameter 1.0 x 102 nm. What are the volume and surface area of each sphere? V = _ and SA = _ How many spheres are required to give a total volume of 1.0 cm3? What is the total surface area of these spheres in square meters? _ spheres, total SA = _ m2 The dispersed phase of a certain colloidal dispersion consistes of spheres of diameter 1.0 x 102 nm.
A solution is prepared by adding 0.166 moles of Mg(NO3)2 to 1.00 mole of water. Calculate the vapor pressure of this solution at 55 °C.The vapor pressure of pure water at 55 °C is 118.1 Torr. Assume that the Mg(NO3)2 is completely dissociated
Compound XY is an ionic compound that dissociates as it dissolves in water. The lattice energy of XY is -592.7 kJ mol1. The hydration energy of its ions is -614.3 kJ mol-1. Write the thermochemical equations for the two steps in the formation of a solution of XY in water. Draw an enthalpy diagram for the formation of this solution. What is the net AH for the formation of a solution of XY? kJ mol-1 eTextbook and Media
Which of the following is a proper procedure for creating a supersaturated solution of potassium nitrate if you have 100g of water and 80g of potassium nitrate available? Add all of the solute to 100g of water and stir for an extremely long time. Add all of the solute to 100g of water and heat it up past 48 degrees C. Add all of the solute to 100g of water & heat it up past 48 degrees C. Make sure everything dissolves, and then carefully cool it down below 48 degrees C. Add all of the solute to 100g of water & heat it up just over 35 degrees C. Once everything dissolves, cool it down to below 35 degrees C. It is impossible to make a supersaturated solution of potassium nitrate with 80g of solute & 100g of water.
The freezing point of benzene, C6H6, is 5.500 °C at 1 atmosphere. Kf(benzene) = 5.12 °C/mIn a laboratory experiment, students synthesized a new compound and found that when 11.98 grams of the compound were dissolved in 212.6 grams of benzene, the solution began to freeze at 4.500 °C. The compound was also found to be nonvolatile and a non-electrolyte.What is the molecular weight they determined for this compound? ?g/mol
Question 7 (1 point) Which of the following would decrease the rate of solvation for solid NaCl in water? A stir bar is added to agitate (mix) the solution. The pressure is increased from 1 atm to 2 atm. The temperature decreases from 50OC to 200C O The NaCl is crushed into small pieces using a mortar and pestle.
1. Suppose that you add 27.5 g of an unknown molecular compound to 0.250 kg of benzene, which has a Kf of 5.12 oC/m. With the added solute, you find that there is a freezing point depression of 3.58 oC compared to pure benzene. What is the molar mass (in g/mol) of the unknown compound? 2. What is the freezing point (in degrees Celcius) of 3.70 kg of water if it contains 187.4 g of CaBr2? The freezing point depression constant for water is 1.86 oC/m and the molar mass of CaBr2 is 199.89 g/mol. 3. What mass, in grams, of NaCl needs to be added to 1.6 kg of water in order to create a solution with a freezing point of -5.6 °C? The freezing point depression constant of water is 1.86 ºC/m.
A 10.00 mL sample of ethanol is added to 250.0 mL of water in order to observe the freezing point depression of the water. Consider the possible errors in this experiment, and determine whether each would cause the freezing point of the water to increase, decrease, or remain the same compared with the expected results. It is discovered that the 10.00 g ethanol sample is actually 95% ethanol and 5% water. The ethanol sample is left out for several minutes before being added to the water, allowing a significant amount to evaporate. Instead of starting the experiment with room temperature water, the experiment is started with cold water. Some of the water is splashed out of the container before the ethanol is added. Some of the ethanol and water solution is spilled out of the container during temperature measurement.
Q2: High pressure (2-5 atm) is applied to increase the solubility of CO2 in soda. When a can of soda is open, the pressure drops to 1 atm. If you leave the can open for a long time, the soda will taste flat. How can you explain this in terms of solubility and pressure?
It says the answer should be 22.98 torr but I have no clue how to reach the answer. Any hints are great. Thanks!
What is the freezing point of an aqueous FeCl₃ solution made to be 0.81 m FeCl₃? (Kf for water is 1.86 °C/m)