Which of the following statements is FALSE about transverse shear stress of a rectangular beam? Select one: O a. The maximum shear stress is at the neutral axis O b. The variation of the shear stress along the depth of the section is parabolic O c. The top fiber has zero shear stress O d. The variation of the shear stress along the depth of the section is linear

Which of the following statements is FALSE about transverse shear stress of a rectangular beam? Select one: O a. The maximum shear stress is at the neutral axis O b. The variation of the shear stress along the depth of the section is parabolic O c. The top fiber has zero shear stress O d. The variation of the shear stress along the depth of the section is linear

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. For the given state of stress, determine the principal planes, the principal stresses, the max shear stress. You must use Mohr's Circle. 20 MPa 32 MPa 55 MPa
The bronze shaft is formed by attaching a hollow shaft to a solid shaft. The allowable shear stress of bronze is 100 MPa. Use G = 35 GPa for bronze. a. If the torque applied is 15 kN m, determine the maximum shearing stress developed in the bronze shaft b. Determine the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 100 MPa or an angle of twist of 3.5 in the 3.5-m length.
Solve alll subparts b, c, d and e B) determine the principal plane (for σmax) in radians. C) Determine the shearing stress in a plane, which is 330 with the vertical (clockwise). D) determine the normal stress (in MPa) in a plane, which is 330 with the vertical (clockwise). E) determine the minimum values of θ (in radians) for which the normal stress is the equal to or less than 35.2 MPa.
30 mm C A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and C. Sketch the bending stress distribution on the cross section. - Assume that the cross-section has a moment of inertia about the neutral axis of 1.907 x 10-4 m². - Assume that the neutral axis is located 97.5 mm from the bottom of the cross-section - Assume the internal bending moment M = 61.4 kN.m
12
Problem 5: The stresses on the x-y-axes are o, = 8 ksi, o, = 12 ksi, and Ty = -5 ksi. Draw the Mohr's circle for this stress state. Identify the maximum shear stress from the Mohr's circle, and draw the maximum shear stress element, specifying its orientation.
The solid shaft is fixed to the support at C and subjected to the torsional loadings and axial load P as shown. a. Determine the torsional shear stress at Point A (50mm from the center) and Point B (on the Surface) b. Determine the absolute maximum torsional shear stress in the shaft. c. sketch the state of stress at point A and draw its corresponding Mohr’s Circle of stress. compute the principal stresses and maximum in-plane stress. T=10.38kN-m
len 9
(Problems No. 1 - 3) The state plane stress at a point is represented by the stress element below. Determine the stresses acting on an element oriented 30 degree counterclockwise respect to the original element. Calculate the shearing stress at the xy-face 60 MPa 20 MPa 90 MPa O a. -55 MPa O b. 65 MPa 55 MPa O d. -65 MPa
The stresses acting on an element are dx = 745 psi, ay = 615 psi, and Txy = 430 psi. (Consider only the in-plane stresses the stresses in the x-y-plane). Oy Determine the principal stresses (in psi) and angle of the principle planes (in degrees counterclockwise from the +x-axis). (For normal stresses, use the deformation sign convention. For maximum shear stress, enter the magnitude.) %1 = psi 0₂ = psi psi max = 8p = Show the stresses on a sketch of a properly oriented element. (Submit a file with a maximum size of 1 MB. Your submission will be graded by your instructor after the due date based on its accuracy. Your grade may change.) Choose File No file chosen This answer has not been graded yet.
In figure shown, the allowable normal stress is 3.5 ksi, allowable shear stress is 1.1 ksi, If t 1.9 in. and b= 3.8 in., 3 in. a. determine the largest P, which is vertical, the frame can 3 in. carry 30 b. determine the largest P, which is normal to AC, the frame can carry
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.18 in. In segment (2), the normal strain is measured as 1,650 pin/in. Assume L₁ - 34 in. and L₂-83 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. (1) Answers: (a) in.& (b) = 4 i B (2) 4₂ in, pin/in.