Which of the following most nearly gives the x-coordinate of the centroid of the entire figure in m.? O-0.18 -0.10 0.18 Ⓒ 0.10 2m 2m

Q: a. Determine the centroid of the area shown with respect to the indicated X and Y axes. b. Determine…

A: As per company policy we can only answer first three questions. Kindly post other questions as…

Q: Determine the resultant of the six forces acting on the sides of hexagon given that each sides…

A:

Q: A bridge is to be built across a 7.5 m wide almost rectangular river with uniform flow depth of 2.5…

A: n=0.003

Q: Resolve F, into components along the u and v axes and determine the magnitudes of these components.…

A: Given data,  F1 = 250 N F2 = 150 N Resolve the F1 and determine the component of these force.

Q: 2g +0.501 20/3 T=0.50 b. Calculate the moment of inertia about the centroidal x-axis -f inortin ahnt

A:

Q: 22 - Find the center of gravity M of the three dimensional homogeneous wire ABCD using the…

A: bfrom the figureABX1,Y1,Z1=36,12,0L1=24BCX2,Y2,Z2=24,24,12  L2=24CDX3,Y3,Z3=18,24,24  L3=36

Q: a) top most, lef tmost FIND: 6) botton-most, right-most 3cm S.ם r = 1,25 y 125 } 05 Vb cm 1.5 3 I…

A:

Q: Determine the distance z̅ to the centroid of the shape that consists of a cone with a hole of height…

A: This problem is based on centroid  of a conical shape. At this point whole mass of body is supposed…

Q: Using ONLY 2 sub-areas (present your calculations in a table): a) Determine the centroid [m] for the…

A: The dimensions of the given figure are marked after splitting it into two rectangles as follows

Q: The x component of vector A is -25.0 m and the y component is 10 40.0 m. (a) What is the magnitude…

A:

Q: Find ex, ey and y. NOTE: ex and ey in mm/mm and y in radians

A: Strain in x and y directions should be calculated and the shear strain should also be calculated.

Q: 4) Calculate the location of the centroid of area (X,Y) and the moment of inertia about the center…

A:

Q: (ZZ+10) (ZZ+10) AA -5m5m AA 8 m 2 m FR (N) y

A: FR = - 20 k + 20 k - 68 k - 68 k = -136 k  N (↓) Taking moment with respect to O. MR = ∑r × F = MRx…

Q: Vectors A and B have equal magnitudes of 8.00 units. The sum of A and B is a vector with a magnitude…

A:

Q: determine the coordinate (in inches) of the centroid of the fig. shown measured from the indicated…

A:

Q: 50KN 20KN/m 20KN/m 3m 3m 2m 2m

A: Draw SFD and BMD

Q: Determine the x-coordinate of the centroid of the shaded area by integration.

A:

Q: 75 mm 25 mm G0 mm 25 mm 25 mm 125 mm

A: solution  consider the  the axis left to y axis as negative and right side of y axis as positive

Q: a. Determine the centroid with respect to the indicated X and Y axes of the area shown. b. Determine…

A: For the plane diagram, the moment of inertia for centroidal axis and reference axis x and y can be…

Q: Determine ỹ, which locates the centroidal axis x' for the cross-sectional area of the T-bar, and…

A: Calculating the area of the different segments with their centroids: Segment Area (mm2) y (mm)…

Q: Determine the x. Measure

A:

Q: Locate the centroid of the shaded area ABC

A:

Q: 1. There exists a void area in the rectangle as shown, a) Find the location of the centroid, i.e.,…

A:

Q: Determine the distance y̅ to the centroid of the area and then calculate the moments of inertia Iu…

A: Consider the figure.

Q: Find the moment of inertia Ix'x for the cross-section shown, Point C is the center of area for the…

A: Consider the figure,

Q: Determine the area and the centroid (x, y) of the area

A: In solid mechanics, there can be any possible shape of the cross-section, for analysis of various…

Q: The triangle has a base of 120 mm and a height of 237 mm. 38 Determine the moments of inertia 1, and…

A:

Q: F, 300N 60 13 12 F 500N

A:

Q: , b) Çalculate Q3) the moment of inertia of the coordinate axıs passıng through the center of…

A:

Q: Τ (iii) Determine the centroidal coordinates of the shaded area in Figure (a). The dimensions are in…

A:

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.