Which of the following is NOT TRUE as an assumption in the elastic analysis of circular members under torsion? O Circular cross sections do not warp as they twist. OTwisting of the circular member results to axial strain on the shaft. O The length of the shaft and its radius remain unchanged. Radial lines remain straight and radial as the cross section rotates

Which of the following is NOT TRUE as an assumption in the elastic analysis of circular members under torsion? O Circular cross sections do not warp as they twist. OTwisting of the circular member results to axial strain on the shaft. O The length of the shaft and its radius remain unchanged. Radial lines remain straight and radial as the cross section rotates

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Give me right solution
The light rigid bar ABCD as shown is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the allowable load P if the stresses are not to exceed 60 MPa and 150 MPa in the aluminium and steel, respectively.
Problem 1 Please choose the correct answer and also write down your solution. (1) The beam is subjected to the shown loading. What is the correct statement regarding the flexural stress at A and B? P P a. Both og and og are tensile stress. 0.5 m 0.5 m 0.5 m b. Both oa and og are compressive stress. Og is tensile stress and og is compressive stress. с. d. OA is compressive stress and og is tensile stress. A В (2) The cantilever beam is subjected to the load P and has cross section as shown. What is the ratio of the magnitudes of the maximum tensile and compressive flexural stresses over the a-a cross section? b. 3/7 a. 7/2 d. 2/10 е. 3/10 h. 10/3 c. 7/3 f. 10/2 i. 1/1 g. 2/7 250 mm 20 mm 60 mm 200 mm 2 m 1 m 15 mm 15 mm
The beam is loaded by two point forces P. The beam is assembled according to the cross-sectional view by nailing wooden parts with cross-sections of 50 mm x c = 220 mm and 25 mm x d = 260 mm. How large can the value of the load P be when the distance between the nails in the longitudinal direction of the beam is 100 mm, the cross-sectional area of the nail is 9 mm2 and their permissible shear stress is 110MPa? Then calculate the maximum stresses and shear stresses of the beam at that load when the distance between the articulated supports is L = 1.9 m and the length of the beam projections a = 1.3 m. Permissible shear force of one nail? kN Static torque of the cutting surface? mm^3 Maximum torque change in cantilever? kNm Cutting force of the projection? kN Magnitude of force P? kN Calculated with the obtained force P maximum normal stress? MPa shear stress maximum? MPa
ASAP Hi! Can you help me with this problem? I'm having trouble answering this, I will give thumbs up for your answer. Thank you!
Q// A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm', determine the stress in each section. 4P Steel Bronze Aluminum P 609.6 mm 914.4 mm 762 mm
1
3. Two bars are made of a material with the stress-strain diagram as shown. Find the cross-sectional area of each bar so the bars fail at the same time with the load is P = 4 kips. Use a factor of safety of 1.8. 3 ft 4 ft P B σ (ksi) 25 20- 15 10- 5H 0 0 tension. compression 0.20 0.40 0.60 0.80 e (in./in.)
The horizontal bar ABC is supported by a pin at A and two rods with identical cross- sectional areas. The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the force in each rod when the force P = 80 kN is applied. Use Est = 200 GPa and Eal = 70 GPa. %3D Steel Aluminum A B T2 m- 1.5 m- Im
Problem 1: The rigid bar ABC is supported by AD and BE. Determine: a. Inclination of member ABC after loading b. 8 at point E Members Properties: Member Materials Modulus Cross- sectional Area of Elasticity AD Aluminum 70GPA 450mm2 ВЕ Steel 200GPA 550mm2 E O •Im O:3m 45kN. t 0 4m
Part1,5,6 please
N = 7