Which of the following is not a true statementabout blade fuses?a. They are available in several different sizes.b. They are color coded according to their voltage capacity.c. They are normally in an underhood fuse block.d. They allow the vehicle’s electrical system tobe broken down into small circuits.

Q: If a ground circuit test reveals a voltage drop of morethan 0.2 volt , the problem may be ___.a. a…

A: Given Ground circuit To find Problem if there is a drop of 0.2 volt

Q: What to do if a thermostat reading seems wrong

A: Given Data⇒Thermostat reading wrongProblem definition⇒Problem says What to do if a thermostat…

Q: Describe the differences between an overrunningalternator pulley and an alternator decoupler pulley

A: The overrunning alternator pulley is an evolution of the alternator's fixed belt pulley. It…

Q: Who is correct?

A: 1. As par Faraday's Law Of Induction "The megnitude of emf induced into the conducting loop is…

Q: Which of the following systems is designed to reduce NOX?   VVT…

A: EGR (Exhaust Gas Recirculation) system and how it works to reduce NOx emissions: Purpose: The…

Q: True or False? Detonation is usually caused by retarded ignition timing.  a. True    b. False

A: Detonation is a phenomenon in the spark-ignition engine (SI engine). The phenomenon in which the end…

Q: Which of the following is commonly used as a transmissionneutral start switch?a. Mercuryb.…

A: Given Transmission neutral start switch To find Technology used

Q: 3. The intersection is controlled by traffic signal or by police officer, is called ... uncontrolled…

A: An intersection is a road junction where two or more roads either meet or cross at grade. This…

Q: Which of the following is not part of the starter motorcircuit?a. Batteryb. Starting safety switchc.…

A: given; Which of the following is not part of the starter motor circuit?

Q: How to adjust the timing by using timing light Explain preignition Explain detonation

A: How to adjust timing light by using timing light Preignition Detonation

Q: What is the basis for the thermostat resetting?

A: An electromechanical thermostat typically contains either a bi-metal coil or a metal strip. When…

Q: What are the two ways in which ventilation can be controlled?

A: Ventilation is basically an opening used to regulate the flow of air to maintain a certain regulated…

Q: The amount of fuel added to the engine depends on Select one: a. Injector pulse width b. injector…

A:

Q: 2 is a symbol for_. 1 3 O a. 3/3 DCV normally Open b. 2/3 DCV normally closed c. 2/3 DCV normally…

A: It is required to choose correct Answer

Q: What are Ball and socket connections

A: The ball and socket connection  also known as spheroid joint, is a type of joint in which the…

Q: What happens when the low-voltage current flow inthe coil primary winding is interrupted by the…

A: Primary winding and scendary windings aare used to increases or decreases the current and voltage…

Q: A rotating magnetic field inside a set of conductingwires is a simple description of a __ .a. DC…

A: Given data : Rotating magnetic field

Q: Technician A checks a starter’s field coils for opensby connecting an ohmmeter between the…

A: Given Starter’s field coils check To find Which technician is or are correct

Q: b.has air-conditioning and is an automatic.c.has air-conditioning or is an automatic.d.has…

A: Air conditioning :- It is defined as the simultaneous control of temperature of air, velocity of…

Q: What is indicated by a reading of battery voltage on the ground side of a component?

A: Voltage, which is measured in volts, is the unit of current in your battery. If you imagine your…

Q: When replacing a thermostat, all these statements are true EXCEPT: Select one: a. Clean the mating…

A: Given :-  When replacing a thermostat, all these statements are true EXCEPT: Select one: a. Clean…

Q: What happens to an electrical circuit when thereis unwanted resistance in it?

A: Given Data : Electric circuit

Q: Where in the shop should a list of emergency telephone numbers be posted

A: The list of emergency numbers shall be posted at the entrance and exit of the shop so that people…

Q: How long is the seat belt light illuminated after the ignition is turned on? A. 3 seconds with or…

A: A seatbelt is a safety device in vehicles to secure the driver and the passengers against harmful…

Q: e voltage is measured

A: For measurements of voltage voltmeter is used in solar cell

Q: Which of the following is a place where the TPMS antenna can be mounted? Under the passenger seat…

A:

Q: A load is an electrical device that__________.a. produces electricityb. directs the flow of…

A: Load  is referred any device/equipment connected to electric circuit which consumes electricity and…

Q: 18. Small welding shops generally wire their power sources to what voltages? O A. 220 V/AC O B. 480…

A: For general arc welding processes, we require normal voltage and current at the input and high…

Q: Explain with a diagram how the bimetallic temperature switch is use to measure

A: Bimetallic temperature switch to be explained with diagram for the measurement.

Q: What is a flame rollout safety switch used for in heating applications?

A: Due to improper maintenance of combustion chamber a problem arises which is called Flame rollout.

Q: Proximity sensors are used to detect the presence of some object. O a. False O b. True

A: A sensor which is used to detect the nearby object without any physical contact is known as the…

Q: While testing variable resistors: Technician A saysthat while checking a rheostat with a voltmeter,…

A: Given Variable resistor To find Which technician procedure is correct

Q: Di ignition systems are capable of producing higher electrical energy than the DIS ignit

A: given: Di ignition systems are capable of producing higher electrical energy than the DIS ignition…

Q: Technician A says that installing a thermostat incorrectly can cause the housing to break.…

A: Solution:

Q: Who can override the Emergency Push Button (override Control Governor)

A: The Emergency Push Button or Emergency Stop Button is a safety feature designed to stop a machine or…

Q: Wiring harnesses are typically shielded by plasticconduit. What color is normally used to shield…

A: SRS is the abbreviated form of supplemental restrain system. these are the wiring or connectors are…

Q: Which of the following is not a Gen2 plasma ignition system? O Dual frequency drive O Capacitive…

A: ignition system: The ignition system create an electric spark in the engine combustion chamber,…

Q: While discussing inductive charging technician a says most current begs use this system because it's…

A: Let's first understand inductive charging Inductive charging: Inductive charging is basically a…

Control transformer

A Control Power Transformers refers to a two-winding transformer that converts an electrical voltage from one value to another using the concept of mutual inductance. The Control Power Transformers help to control/switch the main circuit components. Therefore, the transformer that provides a lower or higher voltage supply to the industrial controls for control circuits like motor starters, controllers, etc., refers to as Control Power Transformers.