Which is not a major component of a steam power plant? A) boiler B) heat supply system C) generator (D turbine Question 6 Which statement below is advantageous to steam power plant? A) air pollution from smoke fumes B) costly to run compared to other plant requires less construction and less cost D above all

Which is not a major component of a steam power plant? A) boiler B) heat supply system C) generator (D turbine Question 6 Which statement below is advantageous to steam power plant? A) air pollution from smoke fumes B) costly to run compared to other plant requires less construction and less cost D above all

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

REHEAT CYCLE / REGENERATIVE CYCLE
A rankine turbo-generator unit receives 27,000kg/hr. of steam at 1.20 MPa and superheated by 122 degrees. condensate leaves at 22 degree celsius, for brake steam rate WB= 4.74 kg/kwhr, mechanical efficiency of 90% and generator efficiency = 94%. Determine the A) ideal work B) Work net C) Ec, cycle thermal efficiency D) W indicated E) indicatedsteam rate F) Indicated engine efficiency G)turbo generator output in KW(Wk)
Thermofluid 4. I his question requires you to demonstrate your knowledge and understanding of gas turbine engines. A small aircraft is powered by a single-spool turbojet engine with a convergent nozzle. It flies at a velocity Vo = 226 m/s and at an altitude where the ambient pressure is 79,500 Pa. The engine intake supplies air at a total pressure and temperature of 101,846 Pa and 300 K respectively. a) b) Draw a process diagram for this engine showing your stage notation and mechanical linkages; Using engine performance data given in Table Q4, determine the engine thrust and thrust specific fuel consumption, stating any assumptions made. Intake air mass flow rate Compressor pressure ratio Compressor isentropic efficiency Combustion efficiency Fuel Lower Heating Value (LHV) Turbine entry temperature Turbine isentropic efficiency Jet pipe total pressure loss Ycold Cp.cold Rcold 1.4 Gas constants Phot Cphot 52 kg/s Rhot 4 87% 98% 43.1 MJ/kg 1060 K 92% 2% 1,005 J/(kg-K) 287.0 J/(kg-K)…
What is the turbine efficiency of a Hydro eletric power plant if the total power efficiency is equal to 56.25%, drive syste efficiency is 81 5% and generator efficiency is 79.8%? A) 86.5% B) 76.5% 66.6% 56.6%
an ideal reheat turbine with one stage of reheat receieves steam at 8 mpa, 480 degrees celsius. reheat pressureis 0.83 mpa and exhaust pressure is 0.0007 mpa. determine A) heat added B) effeciency cycle C) energy chargable D) engine thermal effeciency
An ideal regenerative cycle is executed with steam generated at 8 MPa, 500 degrees Celcius. Before condensing at 0.014 MPa, steam is extracted for feedwater heating at 0.8MPa. Find: a) Ideal work of the turbine b) turbine thermal efficiency c) cycle thermal efficiency d) draw the actual Ts diagram
R A machine working on a Carnot cycle operates between 300 K and 250 K Determine the COP when it is operated as i) a refrigerating machineii) a heat pumpiii)a heat engine
a steam 8.0 MPa and 485 degree Celsius enters the turbine and expand at condenser pressure of 0.006 mpa for cycle and 1kg of steam. determine A.) heat added, B.) Wnet, C.) Thermal Efficiency. And for the engine, Determine the steam flow and the energy output of 40,000 Kw, E.) Wturbine, F.) Energy Chargable, G.) Ideal Heat rate
This is part two of a two-part problem. Water at 2.0 kg/s enters the boiler at 40°C and 2000 kPa and exits the boiler at 2000 kPa. The heat transfer rate into the boiler is 8 000 kW. The water exits the turbine as a saturated vapour at 400 kPa. What is the power produced by the turbine? + OA) 2651 kW O B) 2751 kW OC) 2862 kW D) none of A), B) or C) Boiler 2 Turbine 3
Question 2: In the Ericsson cycle, the pressure of the air entering the compressor is 100 kPa, the temperature is 35°C and the flow rate is 2.5 kg/s. At the entrance of the turbine, the pressure and temperature are 1.1 MPa and 1300 °C respectively, a) Find the heat supplied to the cyele, the heat thrown from the cycle and the net power produced. b)Find heat efficiency. c) Find the heat received or given in the regeneration process.
3. An ideal regenerative cycle is executed with steam generated at 8 MPa, 500°C. Before condensing at 0.014 MPa, steam is extracted for feedwater heating at 0.8MPA. Find: a) Ideal work of the turbine b) turbine thermal efficiency c) cycle thermal efficiency d) draw the actual Ts diagram
Eastern village installed wind turbine power plant in a capacity of 7,200 KW. If each turbine rated efficiency is 98%, how marry wind turbine will installed if each has 200 KW rated power? 26 wind turbine 30 wind turbine c) 32 wind turbine 36 wind turbine