Answered: Where a 44 V battery is connected to… | bartleby

Related questions

Question

Where a 44 V battery is connected to three resistors and an inductor with values R₁ = 96 Ω, R₂ = 24 Ω, R₃ = 40 Ω, and L = 16 H. The switch has been OPEN for a LONG TIME. A LONG TIME AFTER we CLOSE the switch, what is the voltage across the inductor? (in V)

44.00 V

0.00 V

31.06 V

36.24 V

R2
R1
R3
The next fe
ell
values R, = 96 2, R2 = 24 2, R3 = 40 2, and L = 16 H. The switch has been OPEN for a LONG TIME.
IMMEDIATELY AFTER we CLOSE the switch what

Expert Solution

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

In the figure, & = 134 V, R₁ = 8.500, R₂ = 17.602, R3 = 26.4 02, and L = 2.14 H. Immediately after switch S is closed, what are (a) i₁ and (b) i2? (Let currents in the indicated directions have positive values and currents in the opposite directions have negative values.) A long time later, what are (c) i₁ and (d) i₂? The switch is then reopened. Just then, what are (e) i and (f) i2? A long time later, what are (g) i₁ and (h) i₂? (a) Number (b) Number i (c) Number (d) Number i (e) Number i =8 Units Units Units Units S Units R₁ i₂ {R₂ > > W R₁ > ele
A circuit consists of a 0.80 H inductor and a 3.5 ohm resistor. At t = 0 the current through the inductor is 1.2 A. At what time is the current through the inductor equal to 0.40 A?
An Alternating Current (AC) circuit has frequency v = 60 Hz. In such circuit there are 3 elements. The first one is a long thin solenoid with 4 × 104 turns/m, length of 10.0 cm and a cross-sectional area of 20.0 cm². The second one is a resistor with resistance R = 10.02. The third one is a parallel-plate capacitor is composed of two circular plates with radius 10.0 cmseparated by a gap of 0.05 mm. a) Calculate the angular frequency, w, of the circuit. b) Calculate the self inductance of such inductor and the inductive reactance. c) Calculate the capacitance of such device and the capacitive reactance. d) Draw the following functions on the same graph. Represent them as closely as possible to reality using the values you calculated so far. Use the graph on the back. IR cos (@t) VR IXL COS (@t+. VL = IXL COS VC = IXc cos wt- - - 元|2 元|2
In the circuit diagram R1 = 1760 Ω, R2 = 3130 Ω, C1 = 2.9 μF, C2 = 5.7 μF, and ℰ = 12 V. The switch is closed at t = 0. What is the current in A from the battery when t = 1.018 seconds?
An inductor, battery, resistance, and ammeter and switch are connected in series. If the switch, initially open, is now closed, what is the current's final value? O zero battery voltage divided by inductance battery voltage times inductance battery voltage divided by resistance
The I vs t graph shown below is for an LR circuit without a battery. I (A) 14/ 10.5 7. 3.5 1.5 3. 4.5 6. 7.5 t(s) Determine the time constant of the LR circuit. T = If L = 10 H, determine R. R = er resistors from highest to low
Initially, for the circuit shown, the switch S is open and the capacitor is uncharged. The switch S is closed at time t = 0. In the figure shown, when the time t is equal to 8.0 s, the charge on the capacitor (in mC), is closest to: a. 4.06 b. 13.2 c. 0.23 d. 2.26 e. 1.33 70 V L www 0.20 ΜΩ 90 μF
A 14.0 mH inductor makes the current drop from 178 mA to 66.0 mA in only 10.0 μs. What is the potential difference across the inductor? 0.00157 V -92.4 V -249 V 157 V
For the RLC circuit shown, the switch is initially in the open position and closes at time t = 0. The component values are R=21k, L=65mH, C=584nF, and the source voltage is V=4V. What is the value of the capacitor current at time t = 0+? That is, find Ic(0). Enter your answer in units of micro-amps (μA). 8=0 (000)
The leads of an alternate current generator with peak voltage AVmax = 100.0V are placed across a 10.02 resistor. What is the average power dissipated by the resistor? 2.00 kW 0.150 kW 0.0500 kW 0.100 kW 1.00 kW 0.500 kW
Time t < 0, the circuit is in DC Steady State. The switch is opened instantly at time t=0. When t<0, I₂ = 7 A, and I₃ = 9 A. R₁ = 5 Ω, R₂ = 4 Ω, and R₃ = 4 Ω. The solution for I₂ is I2 = I 0 e^ − R t / L. With several resistors in the circuit, the question is, what resistance do we use for R? Answer this question (in Ohms).