When your computer sends information to the Internet it will use a ________ shift register to transmit the data.   a LIFO   b SIPO   c FILO   d PISO   e LIFOPP

Q: 5. The instructions that the CPU decodes travel through the Select the correct answer A)Add bus…

A: The answer is given below.

Q: The PC Source Control, which controls the operation of the Mux on the input to the Program Control…

A: The Program Control register is a component of a CPU that stores the address of the next instruction…

Q: the speed transfer memory it is problem The way out of this dilemma is not to rely on a single…

A: The way out of this dilemma is not to rely on a single memory component or technology, but…

Q: Just what do we mean when we talk about "ethics"? Is there ever a time when positive rights like…

A: The systematizing, defending, and advocating of conceptions of good and bad action are all part of…

Q: QUESTION 50 op Address PC Memory Doubleword is addressing mode:

A: "Since you have posted multiple questions, we will provide the solution only to the first question…

Q: Push and Pop instruction can be used to read data from any memory location specified by SP. OTrue

A: SP stands for stack pointer

Q: q .The code sent by the device in vectored interrupt is _____ long. i) upto 16 bits ii) upto 32 bits…

A: Vectored interrupt: It is a processing technique. A number which identifies the particular…

Q: Hardware Interrupts is It is synchronous O It is caused by any internal system of the computer. This…

A: The correct option is  None of the above Explanation: 1. Asynchronous exceptions, or “hardware…

Q: When implementing the jump instruction, what extra hardware is required? ALU O Adder Demux Mux

A: Multiplexer refers to a type of combinational: When the implementer is introduced, more hardware…

Q: Assume the following values are stored at the indicated memory addresses and registers: Address OxFF…

A: To correctly fill in the blank and determine the value for the indicated operand $0x105, it is…

Q: Flag values: Register values: EAX = FF82E2 EBX = FFFh a) What are the flag values and new value of…

A: a) What are the flag values and EAX after the following operation? ADD AH,z AH= FF8 (Higher bytes in…

Q: What is the addressing mode for the instruction at line 9, as shown in the figure?

A: Hello Student. Greetings from my side. Hope you are doing great. Here is your answer.

Q: The term endian refers to a computer architecture's: O address modes. O ability to find the end of…

A: The correct answer is (d) byte order.

Q: On our board the instruction OUT 67, AL will transfer data or information between the MPU and…

A: The, given question is: On our board the instruction OUT 67, AL will transfer data or information…

Q: The addressing mode of the operand address in the register is called _______ addressing

A: There are five different sorts of addressing modes in the  8085 microprocessor: Immediate Addressing…

Q: Line 2 addressing mode is Select one: O a. Memory O b. Register O c. Immediate

A: When two operands are required for the instruction, the first operand is generally becomes the…

Q: True/False Registers are local memory storage spaces to keep intermediate results of calculations.…

A: We are given a statement about computer memory which include register memory and cache memory and we…

Q: Consider two 32-bit variables var1 and var2. Assume that you can only use 16-bit registers. Is it…

A: Is it possible to add these variables using 16 bit registers ? No, it is not possible to perform the…

Q: Intel 8086 microprocessor max memory is: Select one: O a. 65,536 Ob. 1,048,576 O c. 1,000,000 Od.…

A: The first x86 processor from Intel was the 8086. The 8086, which was first introduced in 1978, was…

Q: The CPU sends various data values, instructions and information to the I/O devices and components…

A: As per company guidelines we are suppose to answer only 1 question. Kindly re-post other  questions…

Q: What additional hardware is required when the jump instruction is executed? ALU O Adder Demux Mux

A: Jump instruction is used to transfer the sequence of code into memory address through various…

Q: Question 21 The ________ instruction, works like an assignment statement Group of answer choices…

A: The solution is given below with explanations

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer.