When moving along a curved path, he ___________ a) Leans inwards b) Leans outwards c) Is still d) Leans sideways
Q: 3- What is the mass [kg] of the solid object that will be formed by rotating the y-axis of the…
A: Ang10 degrees Density p-7850kg/m3, a= 30mm, b=75mm, c= 45mm, d=60mm y
Q: ) Unit of Young's modulus is: Select one: a. N/m O b. N/m? Oc. N.m2 O d. N
A:
Q: Q1: A leg has 1.4 m shaft of bone with an average cross sectional area of 3x10-4 m?. If the amount…
A: Given, Length of the bone, L = 1.4 m cross-sectional area of the bone, A = 3×10-4 m2 Amount of…
Q: 1. On the drawing that is attached, what is the maximum line element straightness of the pin before…
A: In this, there are more than one question so we will solve only first question. if you want the…
Q: When using the Method of Sections, if I cut through a member and I assume that the member was in…
A: When using the Method of Sections, if I cut through a member.
Q: he deflection of point B in
A:
Q: The value of strength by using 0.2% offset method equal to which of the following? If the applied…
A: Write the given values of this problem. Strain(∆LL)=0.2%∆LL=0.2100∆LL=0.002F=66.5×103 N
Q: What is the area of the stock file if a 1.5 x 10 5kg mass presses down 2.5 feet high stock file that…
A:
Q: For the section below, without doing any calculations, what is it possible to say about the centroid…
A: Solution:-Given that
Q: force of 4.5N. calculate the pressure exerted by the pin on the board if the area of contact of the…
A: Solution:We know that:Pressure=ForceArea⇒P = FAApplying vlues we get:⇒P=4.5 N1.8×10-7 m2⇒P=2.5×107 W…
Q: me rigid pipe is supported by a pin at A and an A-36 steel guy wire BD gure Part A 4 ft био μA B…
A: Have a look
Q: If the beam attached to a hinge is 4 meters long and weighs 600 Newtons, and the sign weighs 400…
A:
Q: An engine is pumping water from a well 25 m deep. It discharges 0.4 m³ of water each second with a…
A: Let m denotes the mass of water that is discharged in unit time, ρ denotes the water density, V…
Q: Q17. A force compresses a bone by 0.20 mm. The same force compresses a second bone of twice the…
A: Solution:-Given thatcompression in first bone (δ1)=0.2 mmForce in first bone (F1)=Force in second…
Q: A crass host pours the remnants of several bottles of wine into a jug after a party. He then inserts…
A: Given: Diameter of the cork = 1.60 cm The diameter of the bottom of the jug = 14 cm Force applied on…
Q: A horizontal aluminum rod 3.9 cm in diameter projects 7.1 cm from a wall. A 1200 kg object is…
A:
Q: Sl units of shear force is kN/m kN-m m/N O kN
A: As we know shear force at any section is equal to the algebraic sum of the forces.
Q: 20 tN B 8m 1soknm Draw shear and moment diagrams of the beam.
A:
Q: -800 - Dimensions in mm F1 600 F2 F3
A:
Q: The body will remain it is previous shape and size only when the deformation caused by the external…
A: Introduction: The elastic deformation is temporary deformation in the object, it occurs in the…
Q: 3. DETAILS MY NOTES PRACTICE ANOTHER A cylindrical log of radius 0.4 meter, 7 meters in length, and…
A:
Q: 6) Given the stress element with state of stress shown below. If the element below is rotated 22.5°…
A: Given data σx=10 psfτ=6 psfθ=22.5 Here, σx is the stress in x direction. τ is the shear stress. θ is…
Q: Specific gravity: N/A N/A % error Part 4 Density of Wood 7. Redraw Figure 1 a and 1 b and label all…
A: In general forces occur whenever two things physically interact. In the case of things in contact,…
Q: What is the tension force in the wire shown below if it stretches 0.35 cm when tightened if young's…
A: Elongation in the wire, Young's modulus of the wire, Length of the wire, Diameter of the wire,
Q: Calculate the rotational equilibrium of the water bottle on a rotating circle platform. Explain if…
A: The objective of the question is to determine the rotational equilibrium of a water bottle on a…
Q: A torque of 44-kip-in. is applied on an aluminum shaft as shown in the figure. Use G-3.7 × 10 psi. 3…
A:
Q: 5) Determine and select the steel required for both directions (bending and transverse) of a one-…
A:
Q: Q1: A leg has 1.4 m shaft of bone with an average cross sectional area of 3x10-4 m?. If the amount…
A: Original length of the Bone, L=1.4 m Cross sectional area of the bone, A=3×10-4 m2 contracted length…
Q: The unit of which physical quantity is not pascal? A) Moment of inertia B) Pressure C) Stress D)…
A: Unit of moment of inertia is kg m2. Unit of pressure is Pascal. Unit of stress is newton per sq.…
Q: When using the Method of Sections, our textbook inform us that, after you split the truss in two, it…
A: 6. False Either side could be solved first depending on the calculation to be made. The side with…
Q: r end of the steel rod an n the lower end of the ste 0.75 m
A: Given: ∑Mo=00.75Pst=PalPst=2Pal
Q: Based on this illustration, what must be the value of F1 to make the see-saw balanced? * F2 = 50N 3…
A:
Q: Centre of gravity of a 3D object is based on a. Mass b. Volume c. Perimeter d.…
A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…
Q: The bicep and triceps are classified as an involuntary muscle type True False
A:
Q: The ultimate strength of a sample is the stress at which the sample: (explain why) a. remains…
A: Correct option isd. breaks
Q: A 1684 № umform beaun is attached to a vertical wall at one end and is supported by a cable at the…
A: Draw the free-body diagram of the system.
When moving along a curved path, he ___________
a) Leans inwards
b) Leans outwards
c) Is still
d) Leans sideways
Trending now
This is a popular solution!
Step by step
Solved in 2 steps