When a uniform stream flows past an immersed thick cylinder, a broad low-velocity wake is created downstream, idealized as a V shape in Fig. 1. Pressures p1 and p2 are approximately equal. If the flow is two-dimensional and incompressible, with width b into the paper, derive a formula for the drag force F on the cylinder. Rewrite your result in the form of a dimensionless drag coefficient based on body F length Cp = pU²bL

When a uniform stream flows past an immersed thick cylinder, a broad low-velocity wake is created downstream, idealized as a V shape in Fig. 1. Pressures p1 and p2 are approximately equal. If the flow is two-dimensional and incompressible, with width b into the paper, derive a formula for the drag force F on the cylinder. Rewrite your result in the form of a dimensionless drag coefficient based on body F length Cp = pU²bL

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

P1.59 A solid cylinder of diameter D, length L, and density Ps falls due to gravity inside a tube of diameter Do. The clear- ance, Do - D<< D, is filled with fluid of density p and viscosity µ. Neglect the air above and below the cylinder. Derive a formula for the terminal fall velocity of the cylin- der. Apply your formula to the case of a steel cylinder, D = 2 cm, Do = 2.04 cm, L = 15 cm, with a film of SAE %3D 30 oil at 20°C.
Subject: Fluid Dynamics Find the lift force of potential flow a half cylinder. please help me check my solution and verify the answer.
I need the answer as soon as possible
Using Buckingham-pi theorem, find an expression for the drag force (D) of a sphere of diameter (do) falling slowly with a velocity (V) in a large vessel containing a liquid of density (ρ) and viscosity (μ).
Q4) Define the boundary layer, then find the thickness of boundary layer, shear stress, drag force and coefficiet of drag in terms of Re for the velocity profile of laminar boundary layer u/U=4(y/8)-6(y/8)5. Calcate the boundary layer thickness and drag force if the air flows over a sharp edged flat plate 1m long and 0.5m wide at a velocity 0.9m/s, the air density 1.23 kg/m³ and the kinematic viscosity is 1.46*10-5 m/s².
In studying sand transport by ocean waves, A. Shields in1936 postulated that the threshold wave-induced bottomshear stress τ required to move particles depends on gravityg , particle size d and density ρ p , and water density ρ andviscosity μ . Find suitable dimensionless groups of thisthe problem, which resulted in 1936 in the celebrated Shieldssand transport diagram.
2. Consider the boundary-layer momentum equation for steady incompressible flow in two dimen- sions: ди dpe ду du du + po ay dx Assume the viscosity, u, to be constant. What does this equation simplifies to at a stationary solid surface? Based on this result, is a boundary layer more likely to separate in a favourable gradient (pressure decreasing) or an adverse pressure gradient? Sketch the velocity profile of a boundary layer that is attached and one that is separated. pressure
Air at 20⁰c and 1 ATM flows over a flat plate, v= 35 m/s. The plate is 75 cm long and guarded at 60⁰c. Suppose the depth of one Units on Z, count the transfer of Calor from that plate.
Some engineers want a good estimate of drag and boundary-layerthickness at the trailing edge of a miniature wing. The chord and span ofthe wing are 6 mm and 30 mm, respectively and a typical flight speed is5 m/s in air (kinematic viscosity = 15 × 10−6 m2/s; density = 1.2kg/m3). An engineer may decide to make a superseding model withchord and span of 150 mm and 750 mm, respectively. Measurements onthe model in a water channel flowing at 0.5 m/s (kinematic viscosity = 1× 10−6 m2/s, density = 1000 kg/m3) give a drag of 0.19 N and aboundary-layer thickness of 3 mm. Estimate the corresponding values forthe prototype
You are designing an airfoil for a new hobby RC plane. Because of your limited knowledge, you have mistakenly approximated your airfoil as an ellipse with a = 75mm and b = 12mm. Here, “a” is the depth of your wing and “b” is the thickness. Your plane travels through the air at approximately 20mph (8.9m/s). As it does so, skin friction produces a drag-induced heat of 800W on your wind, of length 1m. Properties of Air: k = 0.025 W/mK, Pr = 0.72, v = 1.847 x 10−5, u = 16.84 x 10−6, p = 1.2 kg/m3, B = 1/Tf (ideal gas), TInfinity = 25oC a) What is the Reynold’s number? Hint: “D” is taken to be the thickness for an elliptical crosssection. b) What is the Nusselt number? c) What is the convection coefficient? d) What is the average temperature of your wing? Assume an ellipse perimeter of approximately 200mm.
fluid mechanics sub
B) for the velocity profiles given below, state whether the boundary layer has separated or on the verge of separation or will remain attached ( i) u/U=2(y/8) -(y/8)² ii) u/U=-2(y/8) +0.5(y/8)³ iii) u/U-1.5(y/8) +0.5(y/8)³ Q3: Find the displacement, momentum thickness and energy thickness for the velocity distribution in the boundary layer: F u/U=0.5(y/8) + 1.5(y/8)³ Q4: A) Find the velocity distribution and expression of the maximum velocity and shear stress for a flow between two stationary plates. C B) A laminar flow of oil between two horizontal fixed parallel plates with a maximum velocity 2 m/s and 100mm apart. Canulate the pressure gradient and shear stress. Take µ-2.4525 s/m².