what would the support for the beam be considered ? (choose one of the one ) Unstable interminate determinate.

Q: The neutral axis of the cross-section a beam is that axis at which the bending stress is O(A) Zero…

A: Neutral axis is the axis which passes through beam or shaft . It is the axis at which member are…

Q: need the answer quickly

A:

Q: 3- In the below truss structure, which member yields first? Derive the stiffness matrix in the first…

A: Structural analysis can either be performed during configuration, testing or post-development and…

Q: (a) Determine (@) Determin (b) Determine positive developed the the the momement VC maximum…

A: ### Using ILD calculation of  a) maximum positive SF at C b) maximum positive BM at Cc) Determinate…

Q: The following two statements are made with reference to the plane truss shown below I. The truss is…

A: To check the truss for static and kinematic indeterminacy and choose the correct option.   The…

Q: (a) the normal stresses 01, 02, in both bars (1) and (2). (b) the normal strains &1, 2, in bars (1)…

A:

Q: Problem 1: Determine the force in members DE,EI, JI, FI, and FE of the truss.

A: Solution:

Q: 50 000 N Prob. 2-4 25 000 N Internal Force of Member AG 2. AG = 20 m B 10 m E G F 20 m 20 m 20 m

A: Given data in question  Point loads vertical and horizontal  Span member length  To find out  FBD…

Q: EI EI EI h

A: The lateral stiffness is required to be calculated.

Q: QA3: which Mohr's Circle represent state of stresses for the element under shear stress Tyx Txy…

A: Brief Concept Introduction: Mohr's circle is used to represents the normal and shear stresses on…

Q: Find the expression of the strain energy stored in the beam with flexural rigidity El and loading…

A: GIVEN:

Q: When the normal stresses are at their maximum or minimum values, the shear stresses are zero. We can…

A: 1 true 2 true 3 false 4 true 5 true

Q: 100KN 30° B с 120KN 6 D 60KN DETERMINE THE FORCES MEMBERS AB, FC, GF,

A: We have a truss structure.To find the force in members AB, FC, GF and GD-

Q: What is the assumption of an axial force member? * Elongate the member - Tensile Force (T)(+)…

A: Ans = A,D A negative axial member force implies that member is in compression (shorten the member)…

Q: Members of the following 2-DOF beam system have the same El and length L C. Which of the following 4…

A: Since K12= K21 Hence Statement C and D are Correct Stiffness caused due to rotation such as K11and K…

Q: The brass bar AB and aluminum bar BC are joined at the collar B and fixed at their ends A and C. For…

A: A composite beam with a brass section and an aluminum section is given.Modulus of elasticityThermal…

Q: The plate element is the structural element that has a one small dimension comparing with other its…

A: True

Q: Which of the following is a statically determinate structure? А. Hingr В. Hingr C. Hinge D. Hing Hi…

A: We have to find the statically determinate and statically indeterminate structure from the given…

Q: need the answer as soon as possible

A:

Q: The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an…

A:

Q: Show that the structure factor, S(k)=

A: A structure factor, F(hkl), is the resultant of all waves scattered in the direction of the hkl…

Q: In a 2D truss, a two-force member has two possible forces, they are .(select correct response) or…

A: In a 2D truss, a two-force member has two possible forces, they are tension or compression. In a…

Q: 400 kN 4 3 800 kN 3 m 1 1 3 4 m

A: Solution: Analyse the pin joint truss by stiffness Matrix Method. ∆=K-1×P  Let us find [P] P=800-400…

Q: When the normal stresses are at their maximum or minimum values, the shear stresses are zero. We can…

A: 1- Yes when normal stresses are maximum or minimum, then at that element shear stress is zero. 2-…

Q: • BCD: Rigid structure a =5.0 ft b=4.7 Pt c= 3.2 ft d= 1.5 ft e = 3° tier rod B • Tie rod Ac is…

A:

Q: by elastic buckling, whe ustic range are called...

A: solution of above problem is below:

Q: When the material is strained beyond its elastic limit, the principle of virtual work can still be…

A: Asked: To determine whether the given statement is true or false.   Given statement: When the…

Q: A simply supported beam of span Land flexural rigidity EI, carries a unit point load at its centre.…

A: given- span=Lflexural rigidity=EIunit point load at centre

Q: Subject: Static of rigid bodies Find: Shear diagram of beam 1,2 and 3 with solution thank you!

A:

Q: Stresses at any point in a simple axial member do not depend on the orientation of the plane being…

A: False The stress at a point in a body subjected to axial force depend on the inclination of the…

Q: . Determine the force in members GF, CF, and CD and state if the members are in tension or…

A:

Q: The Cantikver frues Is loaded Deter minc the reacfio n atE. to 20

A:

Q: B found that the member AC is fabricated A frame shown in the above figure, it was When fabricating…

A:

Q: Determine the forces in each member of the truss. State wether it is in tension or compression. Draw…

A: Given: A truss with loading  Required: Member forces

Q: Solve the forces in each members in terms of the force P. Follow the format of the table below…

A: Consider the free body diagram of the truss shown below. Consider the moment equilibrium about…

Q: Check stability of truss Member=11 Reaction=3 Joint=14

A: The question is related with solid mechanics . In this question we are provide with value of number…

Q: Calculate the support reactions of the column element given in the figure. Determine the required…

A:

Q: (a). Indicate whether the members are in Example 26: Determine the force in members GE, GC, and BC…

A:

Properties of materials

A property of a material describes its characteristics and distinguishes it from the others. The material properties are described it in terms of its hardness, color, appearances, and so on. The material properties generally depend on the type of material, or whether it is a metal or an alloy. There are different kinds of material properties such as mechanical properties, thermal properties, physical properties, and chemical properties. Chemical properties describe the material in terms of a chemical change. The mechanical properties come into existence when the material is acted upon by an external load. Thermal properties are associated with the temperature of the material and specific heat.