What will be the rotational speed of a wind turbine that generates a power of 5MW at 140km/hr wind speed? The turbine is having a blade length of 50 meters and the tip speed ratio value of 3.44? 25.56 rpm 75.75 rpm 100.32 rpm O 51.12 rpm

Q: Consider a location where the wind blows at 15 m/s. 2 options with two rows of turbines…

A: INTRODUCTION : The first row and second row of turbines are provided in this problem. During a…

Q: can you include all the calculations step by step please, such as scaling law and propulsive…

A: We apologize for the earlier confusion. The correct solution is given below.μ = 5V = 100 m/sVh​ =…

Q: If number of vanes on turbine is more than required, it will the work produced by the turbine. O…

A: 1.If number of vanes on turbine is morethan required, it will ..................... the work…

Q: Write the components of Sub-Sonic Wind Tunnel?

A: We describe the main components of sub-sonic wind tunnel with small description.

Q: Design an axial flow turbine stage to meet the following expectations. The inlet conditions are…

A: (i) Axial flow velocity, Ca=C2sinα2=500…

Q: D1/ The folle and a fixed r blade speed angle of the fa factor for all Using a suitat (i) Developed…

A: INTRODUCTION : Steam turbines are the prime movers in which the heat energy of the steam is…

Q: Write any four advantages of Vertical Axis wind turbine.

A: Vertical axis wind turbine - it is a type of turbine which has the blades mounted on the top…

Q: Discuss the differences between Pelton, Francis, and Kaplan turbines.

A:

Q: What is gas turbine why it is used for in plant rotating equipment. Briefly explain its working.…

A: The gas turbine are the combustion engines which can convert chemical energy of combustible gases…

Q: The mechanical efficiency of a single-cylinder four-stroke engine is 80%. The frictional power is…

A: The performance of any engine is described by its efficiency. There are mainly five types of…

Q: Consider a turbojet engine with a thrust of 10,000-lb and an inlet diameter of 4-ft. If an airplane…

A: Given that, Thrust of turbojet engine, T=10,000 lb,Diameter of jet, d=4 ft,Mach number,…

Q: Find the boiler chimney diameter if the boiler has a capacity of 320 kW with a combustion efficiency…

A: Given data: The boiler capacity, W˙ = 320 kW. The combustion efficiency, ƞ = 75%. The calorific…

Q: If the wind velocity is: 1 m/s, 2m/s, 3m/s, 5m/s 7m/s turbine will be:

A:

Q: Explain the wind turbine its part and function of each parts, how it will convert energy?

A: I have mentioned the part names and pics with the help of Power point (for the better understanding…

Q: Calculate the blade length of a wind turbine rotor v

A: Given: Power (P)=4 MW=4×106 Wwind speed v=48 km/hr=13.33 m/sAir densityρ=1.23 kg/m3Generator…

Q: I need to know the characteristic uses of vertical axis wind turbines.

A: Vertical axis wind turbine known as those axis of rotation (rotor direction) is perpendicular to the…

Q: Uhe following pasliculars refer to a two- Fow velactty- compounded impulse wheel which foomms of a…

A: "Since you have posted a question with multiple sub parts we will solve first three subpart for you…

Q: The bore and stroke of the cylinder of a 6-cylinder engine working on an Otto-cycle are 17 cm and 30…

A:

Q: 01- Draw the wind turbine power curve characteristics and discuss the regions of the curve. What is…

A: given; draw wind turbine power curve chracterstcis?power coefficient(Cp)=1627wind power(P)=100kwwind…

Q: For the figure shown below, what flow rate is required to produce 4,700 HP if the turbine is 72%…

A: Given:Turbine power = P = 4700 HPTubine efficiency = Diameter of pipe = D = 3 ftLength of pipe = L =…

Q: A large windmill design has a swept area of 1600m2. Assuming it operates at 100% of thetheoretical…

A: The objective of this question is to calculate the expected power output of a windmill at two…

Q: Approximate the theoretical power in wind moving at a speed of 6 m/s with an air temperature of 40°F…

A:

Q: For solution of this problem also sketch velocity triangles and label it. A rotodynamic impulse…

A:

Q: explanation of the performance tests undertaken for a wind turbine. With the options found, give a…

A: given; performance test for wind turbine?

Q: vind speed of 8 m/s, a rotor diameter of 37.5 m, a fixed rotor rotational speed of 40 r/min, and a…

A: Blade tip speed= BTP=πDN60=π*37.5*4060=78.54 m/s a)TSR=BTPwind speed=78.548=9.92 b)TSR=BTPwind…

Q: Which one of the following is not applicable to vertical axis wind turbine? Select one: a. Easy…

A: Option d is correct.

Q: Explain two types of turbine which depend on the action of water on the moving blades

A:

Q: Find the efficiency of engine Input power-1000 J Ouput power-200 J

A: Given data  Input power =1000J Output power = 200J Find efficiency of the engine.

Q: A wind generator rotates at 17 rpm on the rotor (the part with the blades). It is a direct drive…

A:

Q: What is probable length of blade if the wind turbines are separated with the distance of 160 m? a.…

A: we know that , It has long been believed that distances between 6 and 10 times the diameter of the…

Q: Explain the aerodynamic principles of a wind turbine blade

A: The aerodynamics of the wind turbine blade helps us to harness a type of renewable energy, wind…

Q: A 30000-hp turbine is to be installed for a 50 ft head. A 60-cycle current and 96 poles generator is…

A: Calculated specific speed of turbine in rpm.and explaining,  what type of turbine to installed .

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.