what value must R be adjusted in the circuit below to make l: 40mA? Assume V-12V 30mA. 18 V

Q: iii. What is the feedback voltage of the oscillator if the output voltage is 25V?

A:

Q: For the following self-bind cåveuit, find equivalent circuit acpas Bale aud ground. •Vcc RI Baul 3Re

A: The Thevenin equivalent across base and ground:

Q: a) AK type thermocouple is utilized in the figure given below. The reference temperature (cokd…

A:

Q: Q OUT CLK

A: STATE TABLE OF D-FLIP FLOP: D(Input) Qn+1(Next sate) 0 0 1 1   CHARACTERISTICS TABLE OF…

Q: i) Design and draw the circuit of an adjustable positive voltage regulator with output voltage range…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Part IV. Find the maximum peak-peak voltage output without clipping. Present all the results in a…

A: Given data Collector voltage, VCC=15 V Base resistance, RB=280 kΩ Current gain, β=120 Collector…

Q: Draw the input and output wavwforms for the clamper circuit shown below, let Vi 10 v peak and Vr 3V.…

A:

Q: Determine the change in drain-source voltage to achieve the resulting amplification factor for FET…

A: We have an FET with,  Drain resistance (rd) = 2000 Ω transcoductance (gm) = 50 * 10-4 mhos…

Q: A fault has been inserted in the circuit. Repeat some of the measurements carried out on the RTD…

A: The answer as given below:

Q: Make the control circuit made up of a TRIAC and an optocoupler, for one: 2000W lamp, 120vac You must…

A: We need to make a control circuit made up of a TRIAC and an optocoupler, for one: 2000 W lamp, 120…

Q: 3Z The most usual form of op-amp package a.type TO-5 metal cans b.integration packages c.dual…

A: Examples of OP amps used in Electronics circuit design INA180 INA181 TSV911ILT TS911RILT…

Q: a) If we ignore the offset voltage and bias current error, calculate the voltage gain of the circuit…

A:

Q: An analog-to-digital converter outputs an analog voltage. True or false?

A: Given Analog to digital converter(ADC)

Q: 3:- Detine 4 only; Error, Passband, Standard, Negative Temperature Coefficient, Dynamic Range 24:-…

A:

Q: Open water draw of Opamp AOL=105; Supply (source) voltages are ±V=t10 Volts. its stylish Find the…

A:

Q: Complete the table below and show your complete solution. Find the operation region (cut-off,…

A: Given

Q: VC R1 RC C1 Q1 Ry C2 ER2 RE

A:

Q: Ans: 22 MF %23 キ %23 %23

A:

Q: An ammeter has a PMMC instrument with a coil resistance of Rm- 99 Q and FSD current of 0.1 mA, shunt…

A: For PMMC ammeter the current through coil resistance is given and the value of both coil resistance…

Q: Determine Vx and the mode of operation of the PNP transistor shown in the figure below. Assume Is =…

A: Right Answer option  (b) Vx=0.577 volt active Mode

Q: Answer the question quecly please Electronic

A:

Q: Connect a thermistor (Resistance=500 – 1%  per oc ) in a bridge (power supply =9V) with an…

A:

Q: calculate voltage out

A: In this question, we need to determine the resistance RC  as shown the circuit.

Q: Determine (Vo1). (Vez) and (Vas) for the circuit shown below. Vol Vet 200 k 100 An 200 An Vas s00 AD…

A:

Q: How does a Buck-Boost Converter work? Mention the application of Buck-Boost Converter

A:

Q: 4. Given VDD-3.3V and VT-0.55V find Vout for the following Vin voltages (a) 0.6V(b)3.8V(c)8V(d)0.22V…

A:

Q: Instruction: Show complete solution. Use at least two decimal places. Express your answer in…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: In common source configuration the input resistance of a JFET will be approximately____. a.500 Ohm…

A:

Q: 1. For the Fixed bias configuration determine the following: a. IBo b. Ico c. VCEg

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Q1 Given circuit below. BJT is specified to have ß-100 when in active mode and |VBE 0.7V. Find…

A: The given circuit isβ=100.|VBE|=0.7 V.We need to find all the currents, node voltages and mode of…

Q: II. Design and plot the circuit diagram of the oscillator indicating all components values. Given…

A: ii) The Generalized circuit of the LC oscillator can be drawn as…

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.