What type, size, and a number of classical V-belts is recommended for this system.  The motor is rated at 3 Hp, VFD controlled and runs at 1750 rpm under load.  The output speed required is 1075 rpm.  The application is a saw that cuts wood and the environment is dusty. Target center distance is 18 inches, but 16 to 20 inches is acceptable.  Due to clearance constraints, the driven pulley may not be larger than 6 ½ in.  The motor will slide to adjust tension. 8 hours service per day.

Q: An engine may be equipped with all the following belts, except? Select one: a. A serpentine belt b.…

A: Given that An engine may be equipped with all the following belts, except? Select one: a. A…

Q: A 50 Hz pump drive requires a torque of 70 Nm approx. at 1450 rpm approx. for 1 minute followed by 5…

A: To Find : The number of poles, The continuous power rating The required power rating for 200% pull…

Q: Name three factors that determine the torque produced by an induction motor.

A: Given Data : Torque produced by induction motor

Q: Name two (2) conditions under which a noisy input shaft bearing be more noticeable.

A: There is a input shaft in the bearing which has noticeable noise.So there can be various reasons…

Q: A V-belt drive is required from a 10kW, motor to drive an output pulley of 240mm diameter at 500pm…

A: To find:Suitable V-belt and motor pulley diameter for a single belt installation

Q: A ⁵ ⁄₁₆ nut driver with a 1 ¼ inch diameter handle is used to install a ½ 24 UNC 2B machine screw…

A: P=5/16 inch D= 1.25 inches D=2r

Q: If the line of best fit for your torque speed curve is described by the following equation,…

A:

Q: a 8mm diameter hole and a shaft are designed to be mated in a functioning mechanism that works…

A: Given: The diameter of hole, d = 8 mm

Q: In a belt drive design, the angle of wrap correction factor C θ is a function of the angle of wrap…

A:

Q: What is rotor parallelism and how is it checked? I

A: The rotor parallelism is a term related to the brake. When the thickness of the brake's rotor is…

Q: 1750 rpm motor has a 3” pitch diameter drive pulley. It is driving a 9” pitch diameter pulley. What…

A: GivenSpeed of driver pulley ω1=1750rpmdia=3''dia of driving pulley=9''

Q: a 7460 w split-phase motor running at 1750 rpm is used to drive a rotary pump. the pump should run…

A: (a) Write the given data. P=7460 WN1=1750 rpmN2=1175 rpmC=1118 mmD2=292 mm

Q: approximately 1175

A: The peripheral speed v  of  the belt is = πdx/12  =π(200)*1750/12=91629.785mm/min 300ft/min=  30ft…

Q: With the aid of a diagram indicate the difference between static and dynamic imbalance of a rigid…

A: The answer is provided below

Q: List the types of belt drives and chain drives, their operating principle, and their advantages (at…

A: The belts are used to transmit power from one shaft to another shaft by means of pulleys. The power…

Q: 6 Describe how the displacement of the cam follower shown in Figure 8.31 will vary v igle of…

A: Due to the profile of the cam, the cam is commonly called as snail cam. The cam can only rotate in…

Q: The forward and return strokes of the cylinder are to be controlled by separate push buttons. The…

A: The forward and return strokes of the cylinder are to be controlled by separate push buttons. The…

Q: require at least 4.5 HP to deliver the volume of air needed. The owner has also a second hand motor…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.