What power factor would be presented to the supply in each case and which method is the most economical of power?( 10 Marks

Q: the output voltage during the positive half cycle of the input voltage? 2. What will be the output…

A: Given-Information:- To-Determine:- 1. Output voltage during the positive half cycle of the input…

Q: Details is following Fr=6000N Fa=3000N N=2400rpm Find the total life using data in question.

A: As we know Given Data :- Fr=6000N Fa=3000N N=2400rpm

Q: Can you plot in the psychrometric chart for letter C (ADP)

A: ADP is the apparatus due point temperature and the conditions for the ADP are that the process…

Q: 6 ohm 15 ohm 12ohm 150V

A:

Q: the open circuit voltage and

A: Given; In a DC are welding operation, the voltage-arc length characteristics was obtained as,…

Q: Problem Description Using a special device, the valve in a pipe line is to be opened and closed. The…

A: To find: The Closing and opening of the valve using an Electro-Pneumatic circuit. Let's find the…

Q: what is the smallest gage size copper wire that will limit the conductor voltage drop to 5v when 120…

A:

Q: What are the rules of use of SI symbols?

A: There are various rules of use of SI symbols. Some of them are as discussed below 1. Symbols and…

Q: What power should short shaft, 50 mm in diameter, transmit at 750rpm?

A:

Q: explain what happened here.

A: Given: Load current - Voltage graph

Q: Describe the maximum distortion energy theory?

A: The theories of failure are very important to know the safe dimensions of the machine parts or any…

Q: A single-cylinder, 4-stroke, 3-liter gasoline engine operates at 608 rpm and a compression ratio of…

A:

Q: QUESTION 5 Determine the power transmission through the shaft of a car when the torque applied is…

A:

Q: 4- What are the tasks of DC power supply? THE 10-0V 202 exp Volt Amp 1 2 3 4 5

A:

Q: What does the Torque cause a shaft having a circular cross-section?

A: Torque can be explained as the moment of the force about the axis of the shaft. A torque can have…

Q: What is restitution impulse?

A: Fig.1   Consider two bodies A and B of mass M as shown in Fig.1. When body A strikes to body B, a…

Q: Draw and enumerate the following parts of boiler mounting of Fire Tube Boiler and also the…

A: A boiler is a closed vessel or apparatus that is designed to generate steam or heat a fluid,…

Q: When does the moment area method seem to be convenient?

A: The moment area method is convenient when the beam's deflection or slope has to be estimated at a…

Q: Discuss the importance of using (1 ?electrical transformers cuss the most important types of (2…

A:

Q: Q: Estimate the size of fillet weld for the bracket shown in the figure subjected to a complete…

A: To find: The size of fillet weld. Given: The factor of safety is 2. The load is P=5000 lbs. The…

Q: Welding amperes 3. Refer to the following duty cycle-we operating at 125 amperes? Rated du 300 250…

A:

Q: What is the minimum pulley diameter for a 1 HP motor running at 1750 RPM?

A: Given data:

Q: What is the standard 10 lb deflection amount for a properly tensioned belt that spans 42”?

A: Given data:- Length = 42" Tension = 10lb  Find:-  Deflection amount?

Q: The minimum life of the bearing is the life which 90% of the bearings will reach or exceed before…

A: Life of bearing is expressed in hours. It represents that how long a bearing can work before the…

Q: explain why aluminum is commonly used as a conductor in overhead power lines

A: Those aluminum conductors which are used in overhead power lines are  called as ACSR or Aluminum…

Q: Question No. 5 Find out the missing number in the series given below: 6, 13, 28, 59, ?, 249 O 124 O…

A: here, (6×2)+1 =13 (13×2)+2= 28 (28×2)+3 =59 (59×2)+4 = 122 (122×2)+5 = 248

Q: Which of the following situations converts heat energy to mechanical energy?       turning the…

A:

Q: A self-regulating arc is formed during GMAW: (while using small diameter electrode) if

A: Explanation A self-regulating arc or automatic welding we always used constant voltage power source…

Q: Where did the power output value (37,501.88 kW) came from

A: Given data:- turbine efficiency =85% Generator efficiency=95% Power output of the turbine=46442 KW…

Q: When the compressor and motor operate on the same shaft and are enclosed in a common casing is known…

A: This question is based on the concept of semi hermetic sealed compressor

Q: When are the loads considered negative?

A: While analyzing a truss or beam or any other structure, we start by assuming all the members…

Q: a. The value of maximum torque, Tax = 640 lb.ft 167d₂ (d₂²-d₂¹) max Tmax π 16x640×12×1.75 (1.75…

A: The Torsion equation for the circular shaft is given byWhere,T = twisting moment or torque applied…

Q: In a given DC motor, the output power is 20 HP, and the copper losses are 1.1 KW. If the motor is…

A:

Q: The blower requires 20 kW to run at 350 rpm. The power is transmitted by a v-belt shown in Figure 4…

A: Given information, Blower speed = 350 rpm Blower power = 20 kW Blower pulley  diameter = 650 mm…

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.