What point is I13 ?

Q: In the figure shown, knowing that the resultant force acting on the bolt is along the horizontal…

A: Given data: F1=50 NFN=38 N Need to determine the value of unknown force PN.

Q: 8 In a 2 m long pipe the cross-sectional area A-0.4 m². At a given instant a discharge of 0.48 m/s…

A: Given that: length of pipe = L = 2 mcross-sectional area of pipe = A = 0.4 m2Discharge =Q = 0.48…

Q: As shown in the figure below, determine the internal loadings at point C. В 0.1' m 0.5 m A -0.75 m…

A: Apply Equilibrium Conditions for fbd

Q: ... - 24 in.-20 in.→ 20 in. 16 in. 8 in.I 8 in. The above figure is a section of a column. If the…

A:

Q: Find the lightest safe W-shape for the simply supported beam if the working stress in bending is 120…

A: the point load, P = 12 kN The udl = 2 kN/

Q: Q2 A small marble at point A of mass 0.5 kg as shown in Figure Q2 is release downward with an…

A:

Q: B O2 D 3 E 201 F H at D 6 I G Needle

A:

Q: the location, y, of the centroid of the composite (use 4 significant figures for all values): area

A:

Q: b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 28 mm and…

A: Given data: In a four-cylinder four-stroke internal combustion engine Bore diameter d=28 mm=0.028 m…

Q: Q1. A T-section beam supports different loads as shown in Figure 1. Individual data of the beam will…

A: The loading diagram of the beam is where, RA and RB are the vertical reactions at A and B

Q: Determine the critical load for a pinned-end col- umn made of a circular bar of SAE 1020 hot-rolled…

A: Given     Length, L = 800 mm Diameter, d = 20 mm For SAE1020 Young's modulus, E = 205 GPa Find…

Q: Replace the loading by an equivalent single resultant force (Figure 1) Assume F-110 N and F₂=280 N.…

A:

Q: В |C O2 4 D 3 A E (201 5 F D 6 H at c I G Needle

A:

Q: What is the moment-area method?

A: The moment-area method is one of the methods for determining the slope and deflection generated in a…

Q: Given the beam below (beam AB), determine the reactions in A and B, th shear force diagram and the…

A: Given: F= 66 kN q=56 kN/m L=10 m TO determine: Reaction force  To draw: Shear force and bending…

Q: Task (3) you are asked to perform tensile test on specimens of two different materials (A and B) and…

A: G. The above graph shows the elastic hysteresis loop for the elastic region of the stress-strain…

Q: The components of an electronic system are located in a 1.8-m-long horizontal duct whose cross…

A: Given:- k=0.02717W/m.k Ts=65Tf=30 To find:- Total power rating of the electronic devices that can be…

Q: Solve the following model of spring mass system for the given damping coefficients: u"+bu '+u =…

A: Differential equation,u''+bu'+u=sinmtu0=2u'0=0

Q: 2-69. The tapered settling tank is filled with oil. Determine the resultant force the oil ex- erts…

A:

Q: 0.250 DRILL THRU SIX HOLES EQUALLY SPACED 23° 30° CYLINDRICAL PLATE 1" STD 8 PIPE 3" XS BI PIPE 3"…

A: Section A-A represents the following thing.

Q: Calculate the volume (in ft3) of material used in making 350 ft of 2 in. type L copper tubing. ft3

A: Given data  Length of copper tubing (L) = 350 ft For a 2 in. nominal tube size (from the table of…

Q: The above figure is a section of a column. If the said column is subjected to an axial load of FN x…

A:

Q: As shown in the figure below, determine the internal loadings at points A,B and. Consider the…

A:

Q: An air-standard Diesel cycle has a compression ratio of 18, and the heat transferred to the worki…

A:

Q: Q1 A horizontal beam BC is subjected to uniformly distributed load, w and at the same time it is…

A:

Q: A damped spring-mass system is subjected to a force F(t) = 10 cos(3 t) N. The system has the…

A: As per the company policy, we are restricted to solve only first three subpart of one question.…

Q: 2₂- 2m -3 m 600 N m 4 m Determine the reaction at roller A. Express your answer to three significant…

A:

Q: What point is I56 ?

A: Answer: The point G represents "I56".

Q: M25x6-4h5h-23   describe each part

A:

Q: There are three noise sources where each of them operates at 90 + T dB(A) together in the same room.…

A: Given data: Three noises are present Each noise source = 99 dB

Q: 10. The moment of F2 about DC-axis in N.m is a) Zero b)-750 c) 750 d) 600 c) -600

A:

Q: What point is I34 ?

A:

Q: Meaning of 316 in E316T-1

A: Given data : E316T-1

Q: A cable-supported roof carries a uniform load w kip/ft. If the cable sag at midspan is set at 10 ft,…

A: applying equation ,Hhz= Mz  at midspan to analyze the cable between point B and D .Apply the uniform…

Q: 6) Velocity field of a fluid flow is given as follows : V = (2r-y2+1)i- (x-xy)j Based on your ID…

A: Given: Velocity field (V)=(2x-y2+1)i^-(x-xy)j^x1=3y1=5

Q: Determine the reactions and forces (internal loadings) for points A, B, C, D and E as shown in the…

A: GivenFN=61SN=79

Crystalline Imperfections

The crystalline imperfections are described as the geometrical defects in the crystal due to incorrect arrangement of atoms, impurity, vacancy, and many more. It is not possible to achieve a perfect or ideal crystal, practically.