What limitations are observed in making measurements using meter stick
Q: The error in measurement caused by the person using the equipment is O Limiting error O Systematic…
A: The correct answer is Gross Error.
Q: MEASURED USING CENTIMETER RULER MEASURED USING CENTIMETER RULER Measured Diameter d (cm) Measured…
A: Solution: Calculate the relative uncertainty in diameter for dime. ∆Uddime=0.051.76×100=2.84%…
Q: Three students, Tom, Sally and Kevin, did an experiment where the accepted size of nano-particles of…
A: Measurement of length or size is done in units of meter. One nanometer is equal to 10-9 meter. Now,…
Q: how to determine experiment density with of a zinc rod with only the mass, length and diameter, when…
A: Given: Mass of zinc rod, m = 69.5 grams length of rod, L = 34.3 cm Diameter of rod, D=19 cm To…
Q: By what factor would a numerical quantity change if measured in millimeters rather than kilometers?
A: According to question we need to find--- By what factor would a numerical quantity change if…
Q: measurement are classified in categories. State the frameworks of the International Standards,…
A: A standard is physical representation of a unit of measurement. These Standards of Measurement are…
Q: You repeated a measurement 6 times and recorded the time using a stop watch: 5.6s, 4.6s, 4.8s, 5.1s,…
A:
Q: Consider the relative sizes of the items listed in the table. In the column titled "measurement,"…
A: Given : A list of items. Asked to complete the table.
Q: What are Personal Errors? How shall this affect the final measurements? How Shall we minimize these…
A: SOlution: To describe about personal errors and thier effect on the measurement.
Q: what is the relationship between precision and uncertianity in a measurement?
A: Measurement Uncertainity has following parameters: 1) Precision : It given an idea about the…
Q: can measurement be both precise and accurate?
A: Precision and accuracy are two distinct concepts in measurement.
Q: An instrument is used to determine the concentration of a chemical in water. The instrument signal…
A: Given : Relation between instrument signal "Z" and concentration of the chemical "C" Z = kC + P Z =…
Q: The table shows the set of five measurements recorded in a laboratory. The precision of 2nd…
A: The formula for finding the mean of the given measurement is given by, Here, Σx and n represents…
Q: An infant’s pulse rate is measured to be (130.0 + 5.0) beats/min. What is the absolute uncertainty…
A: Given that:- Infant pulse rate=(130+5) beat/min
Q: ive any analyzation about this uncertainty measurement in physics
A: Error in measurement done using ruler is greater than that of vernier
Q: If you are to measure the length, width and thickness of a book, what measuring device will you use?…
A: According to question: For measuring the length, width and thickness of a book, I prefer Measuring…
Q: A student measures the height from which a ball falls to be two-hundred centimeters with an absolute…
A: measure height = 200 cm uncertainty = 2 cm thus, height = 200 cm ± 2cm
Q: An infant’s pulse rate is measured to be ( 132 ± 6 ) beats/min. What is the percent uncertainty in…
A: Given Data: The pulse rate is measured as: 132±6 beats/min
Q: what is the reading in the micrometer ?
A: Least count of micrometer : Least count of micrometer=smallest reading of main scaleTotal number of…
Q: 2. MICROMETER 3. 10 5. - 20 TTTTTTTTT| -15 -20 – 10 MICROMETER Total Reading SR TR VR Total (cm)…
A: Diagram which is given in question is micrometer, we have to measure the value, SR,TR,VR value add…
Q: How can you reduce percentage uncertainty in measurement you make
A: Following methods can be applied to reduce percentage uncertainity: 1) Take proper measurements and…
Q: What is the micrometer reading given in the last figure of Appendix A?
A:
Q: Which of the following statements is true? A) Electrodynamics is part of Modern Physics. B)…
A: A) Electrodynamics is part of Modern Physics. Modern physics is a branch of physics that developed…
Q: What is the relationship between the accuracy and uncertainty of a measurement?
A: The accuracy and uncertainty are inversely proportional to each other. If the uncertainty is less…
Q: Find the least count of a milliammeter in which there are 20 divisions between 400mA and 500mA.
A: The Least count = range/no.of divisions No. of divisions = 20
Q: Can a set of measurements be precise but not accurate? Explain
A:
Q: A digital micrometer measures the diameter of two cylinders. Cylinder 1 diameter = 15.22 ± 0.02 mm…
A: Uncertainty in difference or addition is given by direct addition of uncertainty in given…
Q: The output of a measurement system is called as True value. Select one: True False
A: The measurement is a process of obtaining a precise quantitative value of a physical quantity. Many…
Step by step
Solved in 2 steps
