Answered: What is/are the advantages of knowing…

What is/are the advantages of knowing how to estimate the additional stress/es due to surface/structural loads? Explain your answer/s.

Construction Materials, Methods and Techniques (MindTap Course List)

4th Edition

ISBN:9781305086272

Author:William P. Spence, Eva Kultermann

Publisher:William P. Spence, Eva Kultermann

Chapter3: Properties Of Materials

Section: Chapter Questions

Problem 4RQ: How does a tensile stress differ from a compressive stress?

See similar textbooks

Related questions

Q: When do you begin to account for tension stiffening?

A: The word "tension stiffening" is described as the impact on the stress of steel reinforcement of…

Q: Describe about the deviator stress.

A: - Deviator stress is also know as Principal stress difference, Shear stress, Back pressure stage -…

Q: What is the difference between normal, shear and bearing stress?

Q: Practice Problem: Refer to Figure 3.70, a flexible square area is subjected to a uniformly…

A: Given: The distributed load (q) is 100 kN/m2. The depth is 4 m. Consider the figure,

Q: Where does “stress at a point” analysis can be applicable?

A: The analysis of stress at a point is applicable to find the mechanical properties of the solid…

Q: In ASTM D245, what is the length of time for duration of load assumed for strength calculations? How…

A: Objective: To study ASTM D245 and answer the following question: 1) duration of load assumed for…

Q: What is the difference between SIMPLE STRESSES, THIN-WALLED, & STRAIN.

Q: ow does the strength changes in multiple axis load?

A: Anisotropic materials are also known as “triclinic” materials. They are direction-dependent mediums…

Q: illustrate normal stresses in cross section.

A: Normal stress is the stress component perpendicular to a given surface, such as a cross section of a…

Q: Discus why the value of compressive strength more than tensile strength.

A: To discuss: Why the value of compressive strength more than tensile strength.

Q: What is/are the important distinction between normal stress, shearing stress, and bearing stress…

A: Stress is a physical term that describes the force applied to a material per unit area.

Q: Two vertical forces, each of magnitude P= 13 kN, are applied to a beam of the cross section shown.…

A: Objective: To determine the maximum compressive and tensile stresses in portion BC of the beam.…

Q: Assuming elastic behavior, why does the maximum shear stress always correspond to the neutral axis…

A: Given data:

Q: Explain how principal stress is different from other normal stresses (tensile or compressive) that…

A: Principal stresses: Principal stresses are the maximum and minimum normal stresses, they occur when…

Q: The wood beam has a rectangular cross section in the proportion shown. Determine its required…

A: Support Reactions : ∑Fy = 0RA + RB = 500×2 = 1000 N .............(1)We know that, At free end of…

Q: What are the advantage and disadvantage for each method in solving for the tendon stress at failure?

A: Pre-tensioning following system are adopted and given below; Hoyer’s system Post-tensioning…

Q: Define the Normal and Shear Stresses on a Plane ?

A: The normal stress is the stress acts perpendicular to the surface of the object.It can be of tension…

Q: hat are the differences between permissible stress and grade stress?

A: Introduction: The applied load divided by the initial cross-sectional area of a material yields the…

Q: Explain the Vertical Stress Due to a Line Load ?

A: The Vertical Stress Due to a Line Load:

Q: The beam with cross-section shown carries a uniformly distributed load of intensity wover its entire…

A: Calculating the reactions at A and B: RB+RC=4.5w∑MC=03RB+w×0.522-w×4×2=0RB=2.625 wRA=1.875 w

Q: What is neutral stress?

A: It is the stress or pressure which the pore fluid transmits. This is also known as pore strain,…

Q: 1. The structural I-beam supporting a floor load of 4.6 kN/m2. The beam meters and are simply…

Q: Draw the Stress-Strain Diagram and label it properly.

Q: Describe about the Total Stress Method.

A: At any given plane section in the soil mass total stress is defined as the sum of the self weight of…

Q: Explain Effective stress method.

A: Terzaghi was the first to articulate the principle of effective stress. Effective stress concept…

Q: A 3ft long bar with a 1in x 1in cross section is subjected to a 14,153lb tensile load. What is the…

A: Area of cross section ( A ) = 1 in2Tensile load (p ) = 14153 lb Tensile stress = ? Ksi

Q: Define the term principal stresses.

A: These are maximum and minimum normal stress.

Q: Find max and min stresses. Please provide step by step solution. Don't copy!!

A: Given data: D = 9.5mmd = 9mmr = 2mmkf = 1.48Bending Moment Max = 38.5Nm…

Q: In terms of the stress-at-a-point analysis, define what is principal stress?

A: - Principal stress is defined as the maximum and minimum normal stress which may act on a point in…

Q: what is the maximum bending stress ?

A: Given: Support reactions and loading of a beam Required: Maximum bending stress

Q: Define and explain all the different types of stress and strain with the help of neat sketches…

A: The ratio of force to per unit area is known as stress. It's unit is N/mm2 . σ=PA where, P= force…

Concept explainers

Pressure and Stress

Question

What is/are the advantages of knowing how to estimate the additional stress/es due to
surface/structural loads? Explain your answer/s.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In terms of the stress-at-a-point analysis, define what is principal stress?
How does the strength changes in multiple axis load?
What are the differences between permissible stress and grade stress?
(a) Assuming elastic behavior, why does the maximum shear stress always correspond to the neutral axis level? (b) An under-reinforced beam section is safer than an over-reinforced one. Is this a correct statement? justify your answer using a neat sketch. (c) What are the two fundamental equations/conditions in beam flexure analysis? Explain their use using neat sketches.
What is/are the important distinction between normal stress, shearing stress, and bearing stress from each other? How do they different from each other?
In ASTM D245, what is the length of time for duration of load assumed for strength calculations? How does changing this duration affect the allowable stress?
what is the muddiest point in stresses and strains concepts and calculations?
Define and explain all the different types of stress and strain with the help of neat sketches clearly showing the directions of application.
Differentiate Allowable Stress Design (ASD) with Allowable Strength Design (ASD) design procedure. Give examples as much as possible.
what is the maximum bending stress ?
W A 3ft long bar with a 1in x 1in cross section is subjected to a 14,153lb tensile load. What is the tensile stress in ksi? Answer to two decimal places. Type your answer...
Define the term principal stresses.