What is the total load on B-1 if the load rate is 80#/ft^2 (B) 24-0" 1-5 8'-0" C12" BRICK WALL 8:0" * * B-1 SLAB SPAN 8-0"8-0" 8-0" * 8'-0"

Q: 2- A sign weighs 2000 lbs. The design spectral acceleration was determined and found to be SDs =…

A: Solution: Given: Base = 40 ft load = 2000 lbs = 8.89 kN SDS = 1.2 gms =1.18x10-5 kN h= Z3 Design…

Q: DL (decking, flooring, etc.) = 10 psf LL (occupancy) 40 psf Beams B-2 Girders G-3 = = 15 #/ft. 50…

A:

Q: 3. Load Tracing Determine the Columns loads assuming: DL (decking, flooring, etc.) = 30 psf LL…

A:

Q: For the beam shown find reactions and draw shear and moment diagrams. A is a pin and B & roller. are…

A:

Q: 1) Graphically trace all the tributary areas for the beams and girders for the framing and desking…

A: Tributary area of a beam , girder or a roof is the area which  cause the loading on that particular…

Q: 矩形截面简支梁,加载于梁中点C,如图示。求amax Imaxo Simply supported beam with rectangular section, loaded at beam…

A: A simply supported beam is given we need to find out  σmax and ?max

Q: 4.4 Refer to the framing span diagrams from Architects' Studio Companion and answer the following…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: Considering the given cantilever beam, columns and their cross-sections in figure 2, then justify…

A: Beam: Maximum bending moment on the beam is Mmax Mmax=50 kN×3 m=150 kNm=150×106 Nmm Maximum bending…

Q: Given a 9ft long column, which is fully Fixed in both directions at the bottom and is free to side…

A: Step 1:Step 2:Step 3: Step 4:

Q: If the hook load is 300,000 b and fast line speed is 400 t/min, fed ho of the prime mover if the…

A: hook load=300000lbfast line speed=400ft/minefficiency=0.92rig has 8 drilling linestackle…

Q: Bending Moment and shear force diagram for overhanging beam Problem 5-3 Determine the values and…

A: To find the Shear force and bending moment diagram-

Q: What is the LRFD time effect factor, A, for a member designed for the 1.2D+1.6L load combination…

A:

Q: In each of the load-tracing problems below, construct a se- ries of FBDS and show the propagation of…

A: The given data is: DL=15 Psf LL=40 Psf Total load=55 Psf   Calculating the span load: Here the total…

Q: My teacher gave us a problem to think about before next class and I'm having a hard time with it…

A: LRFD- It stands for the load resistance factor design approach used in designing different…

Q: d) Calculate the first story column axial load capacity using 8-#11. Verify that the column size and…

A: Answer (d) Calculation of axial load capacity of square column We know that Axial load capacity is…

Q: PLEASE ANSWER QUESTION AND SHOW WORK. I NEED TO STUDY THIS. The SUBJECT IS TRANSPORTATION "Civil…

A: Therefore, the length of the guardrail (X) is approximately 1360.209375 feet.Explanation:Step 1:LH=…

Properties of materials

A property of a material describes its characteristics and distinguishes it from the others. The material properties are described it in terms of its hardness, color, appearances, and so on. The material properties generally depend on the type of material, or whether it is a metal or an alloy. There are different kinds of material properties such as mechanical properties, thermal properties, physical properties, and chemical properties. Chemical properties describe the material in terms of a chemical change. The mechanical properties come into existence when the material is acted upon by an external load. Thermal properties are associated with the temperature of the material and specific heat.