What is the total length of the course AB if the rear tapeman holds exactly 7 pebbles and 5 pins after measuring the course AB and the partial length is 2.30 m? Assume that one tape length is equivalent to 10 m.

What is the total length of the course AB if the rear tapeman holds exactly 7 pebbles and 5 pins after measuring the course AB and the partial length is 2.30 m? Assume that one tape length is equivalent to 10 m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A baseline was measured using 100m tape which is standardized at 15°C with standard pull of 10kg. It…

A: GivenLength of tape, L = 100m.To= 15°C, Tm = 28°CPo = 10 kg, Pm = 16kg, lo= 925.15mγ = 7.86 g/m3,…

Q: Hermie was asked to estimate the perimeter of the Einstein building. He paced the length and the…

Q: 2.Determine the value of W if the 100kg crate is on the verge of tipping forward as it slides up the…

Q: Hill B and Hill C with an elevation of 17.1 meters and 17.2 meters respectively is on a line between…

A: Datum level of tower at point A = 5 m Height of hill B = 17.1 m Height of hill C = 17.20 m Height…

Q: Prepare and complete the differential level notes for the information shown in the accompanying…

Q: Problem 6. A baseline was measured using a 100m tape which is standardized at 15°C with a standard…

A: To find :- True length of Base line After applying correction for temperature and pull to tape.

Q: The area of a rectangular field was found to be 3000 sq. m. after a precise measurement using a 60…

Q: Determine the centroidal moment of inertia. 100mm x 50mm x 10mm C250 x 30 C250 × 45

Q: 4/39) Determine the forces in members BC and CF of the loaded truss, repeated here from Prob. 4/19.…

Q: The cross-section notes shown below are for a ground excavation for a 12m wide roadway. STA 12+1400…

Q: SHOW DETAILED SOLUTION. PLEASE MAKE SURE THAT THE ADJ LATS AND ADJ DEPS ARE EQUAL TO 0.

A: To Find Adjustment of latitudes and departures of the all the course so that their sum can be equal…

Q: 10. In figure below, what is the value of dimension D? * Z DRILL 6 HOLES D 一-十層 -星十章-

A: Diameter of hole = 7/16 Distance between different holes are given in figure

Q: Show complete solution. Round off answers to 2 decimal places. Do not forget to include the units.…

Q: The head and rear tapeman recorded 3 tallies and 6 pins in a line that was measured with a 50 m…

A: To find length of line

Q: Show complete solution. Round off answers to 2 decimal places. Do not forget to include the units.…

Q: ?? 250x(kd)? /2= 8x1473(600-kd) → solve to get kd = 1

Q: Problem #5 a. A 30m steel tape is supported only at its ends and under a steady pull of 7kg. if the…

A: Solution: a) Given: Length of the steel tape, L=30 m Pull, P=7kg Weight of the tape, W=0.9kg

Q: 1) AREA OF RANGE CROSS-SECTION. Soundings were taken along a 38-m long range across a lake (see…

A: The areas and volumes of the different shapes can be determined by different methods used in…

Q: N 48 12' W 428.20 1. Determine the Linear Error of Closure (in meter) and its direction (in DMS).…

A: The given question has multiple sub-parts- Bearings are clockwise or anticlockwise angle formed from…

Q: Convert the following Reduced Bearings into WCB. • N 65° E • 439 15' E S 52º 33' W •N 32º 42' W

Q: Complete the differential level notes shown below and perform the customary arithmetic check.…

A: To Determine Complete the differential level notes and Perform the customary arithmetic check. The…

Q: The length of a water course passing through the fields was measured with 30 m steel tape and the…

A: The Length of Gunter's chain is 66 ft long. It consists of 100 links and the length of each link is…

Q: Using the the following values, please calculate Specific Gravity Corrected G corrected (rounded to…

A: Given, K-value = 1.0004122 Uncorrected G = 2.251

Q: A 30 m. steel tape is 2 mm too long at 20°€. A rectangle is measured with this tape. The sides are…

Q: FH on the curved gate. Is S Water 4m -- -? If the gate width= 6 m F r=1my B 264600 NO 264600 lb O…

Q: Highway curve has R = 800 m, I = 20° 00', and Pl station 3+290.600 m. ▼ Part A Determine degree of…

Q: MALI + 2 MB (L₁ +4₂) + McL₂= = GAIX - 6 Az X z Li L2 pM2Q w(KN/m) B L (m) Draw the V&M Diagram using…

Q: (b) A rectangular slab, simply supported along all four edges, is isotropically reinforced to give a…

A: A rectangular slap is isotropically reinforced and supported along all four edgesThe magnitude of…

Q: "from South Line Leneth Azimuth Theta Lat ad Dep ady Length' 9759 15.382 5.623 Theta Bearing N 17 40…

A: Abs in the picture is the sum of all Latitudes without 'including the negative sign' its type of…

Q: Hermie was asked to estimate the perimeter of the Einstein building. He paced the length and the…

Q: A. FIND THE AREA USING DPD METHOD

A: Given Data:LineLengthBearingAB26.77S56°23'EBC15.91S29°59'WCD25.88N56°23'WDE16.00N26°47'E

Q: REMARKS BM-1 0.95 767.67 ТР1 2.89 8.99 TP2 2.96 7.39 ТРЗ 1.55 8.71 ТР4 1.84 9.83 TP5 2.89 8.55 BM2…

Q: A student was ask to make a 345.43 m long line using a 25 m long tape taht is 0.0021 m long. What is…

A: Given data:

Q: B' and L'? 0.7m - 0.ốm 2.0 m LT 2.0 m

Q: A 100 m tape weighing 30 N is suspended between the two ends under a standard pull of 180 N. The…

A: Given: A 100 m tape weighing 30 N. The tape is suspended between the two ends under a standard pull…

Q: A line was measured with a 50-m tape. There were 2 tallies and 3 pins, and the distance from the…

Q: Given the fence 20 meters long and 3 meters high, determine the total number of pieces of 10mm…

Q: Question- A 100 m tape weighing 30N is suspended between the two ends under a standard pull of 100…

A: Given- L=100 m tape, Weight of tape W=30 N, Standard pull P=100 N, Correct distance between the tape…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

Problem 2: Given are matrices A, B, C and D. 21 -4 -26 7 -1 -2 2 -2 10 -8 A B = -1 3 -13 25 -11 -1 -1 21 -2 25 -18 1 -26 1/3 C =| -16 8. -7 D 10 -100 10y 7 -10 13 -98 1/2 22 Solve for: a) A + D b) 2C – 3A + B – 10D c) B +D - 2C + 3A d) В + D e) С - D
Please correct answer
The cross-section notes shown below are for a ground excavation for a 8m wide roadway. STA 18+700 7.08 0 7.57 4.06 7.27 5.79 Determine the cross sectional area at STA 18+700. Round your answer to 3 decimal places. Add your answer
Q2: In Figure below if width of the gate = 2B, find Fy and its line of action 4 circular arc Water
Please do the Mohr's Circle. Rate will be given!
You measured 300 ul with a 1000ul pipette; The corrected values were the following : 292 ul, 294ul, 287ul, 290ul, 288ul and 293 ul (mean- 290.7 ul and Std. dev + 280 ul) 3. Acceptable values are: Accuracy : 1.0% Precision: 0.5 % Were you accurate? Were you precise? and why? show cakulations
Hermie was asked to estimate the perimeter of the Einstein building. He paced the length and the width of the building and recorded the following data: Trial Length (in paces) Width (in paces) 56.8 42.6 2 56.6 42.7 3 56.8 42.6 4 56.2 42.1 Using a steel tape, he determined that the length of the building is 40.5m. Determine the perimeter (m) of the building. Round your answer to 3 decimal places.
Please solve this question in handwriting. step by step. I am confused. in details
Prepare and complete the differential level notes for the information shown in the accompanying table. Include the customary arithmetic check.
Help me answer the problem question and box the final answer. use 2 decimal places.
determine the relative error of the closure
ENGINEERING MECHANICS (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LNG EXPLANATION. ANSWER IN 2 DECIMAL PLACES.) 9.29 As a round log passes through a sawmill, two slabs are cut off, resulting in the cross section shown. Calculate Ix of the cross section if h = R/2. What is the percentage reduction in Ix caused by the sawing operation?