What is the support moment M, in the beam shown below? 15KN 30 kN/m -1.5 m 1.5 m

Q: How do you convert gpm to ft?

A: A cross-sectional area's flow of fluid is measured in gallons per minute. In simple terms, it…

Q: Course: Quality Engineering How to explain all of the ISO 9000 in a structured way.

A: ISO 9000 certification ISO 9000 consist of a set of international standards on quality management.…

Q: Define Reliability-based design

A: Reliability-based design- It is defined as a  concept that helps in planning, building, and…

Q: Write down the important steps for improving listening skills and vocabulary building

A: 1. Always look at the speaker and maintain eye contact. 2. Use positive body language. 3. Observe…

Q: ultural structure requiring electricity. It is okay if it is a simple floor plan, and it's up to you…

A: A floor plan is a diagram or visual representation of the interior of a house as seen from above. It…

Q: Explain the principle of 5S in Construction. Complete the answer please.

A: Introduction- Construction- It refers to the methods and business associated with assembling and…

Q: What is a pick

A: The term pick may be defined in various ways according to the situation Firstly Pick may defined as…

Q: Reading Settlement Settlemen Specimen Avarage Specimen Height (h) Stress AH/h Stress Different…

A: Stress Range (KPa)   Stress different∆p(KPa) Reading  Settlement      (mm) Settlement…

Q: Define The required diameter

A: A diameter is a chord that runs through centre point of circle. The centre of circle is at midpoint…

Q: Q1: Discuss in detail Kennedy and Lacey Theory? Write down all the design steps. Civil Engineering…

A:

Q: Environmental Effects of engineering constructions projects. Include photos.

A: Environmental engineering : Environmental engineering comprises the development of methods and…

Q: answer in 4 decimal places

A:

Q: Please explain Part B properly. any classification table is there? How is the order and level…

A: Given: Misclosure= 15mm Total length,K= 10 Km Required: Order of levelling

Q: please put it on the paper for better understanding. thanks

A:

Q: What is the most common use of RFI?

A:

Q: Discuss Shape Factors

A: Shape factor:- Shape factor is defined as the ratio of plastic moment and the yield moment of the…

Q: what is ytm

A: There are different type of the calculation done in the funds. The funds can increase or decrease…

Q: What is Third Party Certification?

A: When an item or organisation has the formal verification or authentication of certain…

Q: 2 unsafe acts and unsafe conditions associated with ergonomics and psychological hazards in…

A: Solution- Electrocution, falls from large heights, damages from tools, equipment's, and machine,…

Q: (b) Design the Beam B-B for the maximum sagging section only. Your design should consider the…

A: L=4.55 mh=22.2 mt=122 mmDL=3.55 kPaLL= 4.55 kPafck= 25.5 Mpafy=472 MpaTo design- 1) Loads2) Design…

Q: Differentiate between Directed Changes and Constructive Changes.

A: Directed Changes are the changes that are specifically directed by the owner which may or may not…

Q: What is a Letter of Intent?

A: A letter of intent is a report which shows the general plans of an agreement between two or more…

Q: What do you mean by fail safe design

A: Fail-safe designs are the methods of designs in which various techniques can be used to mitigate…

Q: Give two environmental considerations needed for material production and elaborate.

A: Environmental considerations needed for material production are very important nowadays. Because the…

Q: How to identify if "cos" or "sin" is to be used?

A: If force makes angle with x-axis, cos component will be considered along x-axis and sin component…

Q: 10- Explain about the specifications of design software using empirical mechanistic method.

A: The empirical mechanistic (EM) method is a design approach that combines empirical observations with…

Q: What is the Design mode?

A: In terms of construction, the word design mode refers to the process of creating a specific solution…

Q: QUESTION 2. What is the actual length of the line measured by the Architect scale? ? 0 46 1/8 0 20…

A: A two scales are given, we need to find out the actual length of the line measured

Q: HI, KINDLY IDENTIFY WHERE IS THE ANSWER FOR LETTERS A TO G.

A:

Q: Define Earthquakes.

A: Earthquake is any sudden ground shaking triggered by the seismic waves passing through rocks of the…

Q: GIVE THE FIVE ELEMENTS OF GREEN BUILDING

A: Green building is a design strategy that tries to reduce a building's environmental effect while…

Q: Define each term in three sentences only. 4. Curve Resistance 5. Air Resistance 6. What is AASHTO?…

A: (4.) Curve Resistance - * It is the loss of tractive force when a rear wheel     driven vehicle…

Q: bout construction project managemen

A: The process of using techniques to plan, design and construct a project leading to proper completion…

Q: What is architecture? Describe any 6 architectures styles.

A: Architecture is the art of the preparation, planning, and developing structures and other actual…