What is the pressure in N/m2 at a depth of 2m below the water surface? 18620 N/m2 19620 N/m2 98100 N/m2 19800 N/m2

Q: A piston-cylinder device contains 1.5 kg of steam at 300°C and 0.4 MPa. Steam is cooled at constant…

A: The initial conditions are: The specific volume of the steam can be determined from the steam table…

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: The correct choice is what

A:

Q: Question Completion In the figure below, which of the following represents the dedendum? zeta gamma…

A: Circular pitch is the distance measured from a point on one tooth to the corresponding point on the…

Q: What is the value of w and y? y W 6V2

A:

Q: Says.003 is wrong

A:

Q: If 17 welders can complete a job in 134 hours, how long will it take for 21 welders to do the same…

A:

Q: What is the module of a spur gear with 30 teeth and pitch diameter if 5 inches? 5.236 mm 4.233 mm…

A: The given values are -  Teeth T =30 Pitch diameter D = 5 inch(127 mm)

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: Question 1 The helical steel extension spring has a diameter of 2 inch, wire diameter of 0.1 inch,…

A: Given: diameter of the spring: D=2 inch diameter of the wire: d=0.1 inch for steel shear modulus:…

Q: Iron Ore are mainly used to produce high heat in blast furnace Select one: True False CamScanner

A: Iron ore are mainly used to produce high heat in blast furnace.

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: O I'd love ice-cream I love ice-cream

A: Correct is I love ice-cream.

Q: In a lathe machine tool, when the cutting tool moves parallel to the axis of rotation of the…

A: It is required to justify given statement

Q: Iron Ore are mainly used to produce high heat in blast furnace

A: I think its answer should be False. Because blast furnace is used to melt iron ore by reducing…

Q: The number of teeth on a gear is 27 and the outside diameter is measured as 10 mm. The module of the…

A: Given Data No. of teeth is 27 Outside diamtere is 10mm

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: Read the following statement and choose the most appropriate answers. Statement 1 For a measuring…

A: Accuracy is defined as how close is the measured value to the true value.

Q: Answer in 4-10

A: Given: →h1=3387.31 KJ/Kg→h2'=3074.5 KJ/Kg→h3=3457.04 KJ/Kg→h4'=3109.82 KJ/Kg→h5'=2384.82…

Q: LEASE ANSWER ALL OF THE GIVEN QUESTIONS.   Choose from the given choices/options below the…

A: Given Data : Motion of projectile

Q: Match the following. Forging is an example of Choose. Choose. Drilling operation is an example of…

A: Forging is an example of     Primary shaping process

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: There are several failure modes by which gears can fail. Select the true statement from among the…

A:

Q: That is the answer I have and it is marked as wrong, could you please do it again and see if you get…

A:

Q: Please show all the steps, thanks

A:

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: Name at least two units that you use every day.

A: Most of the time in the day to day life there are many duties which have to be done daily y u. Some…

Q: Write legibly and box the final answer

A: