What is the normal force between the crate and the wedge? What is the smallest force P needed to pull out the wedge?

Q: D 7 kN -15 m- B E 24 kN 8 kN -1.5 m- F 7 kN 0.8 m Find the force in member BC in (kN)

A:

Q: Select the best answer) The plate is supported by a hinge at B and a roller at A. The hinge is usty.…

A: The plate is supported by hinge at B and Roller at A. What are the support reactions?

Q: Calculate the tension in each cable around the pulley.

A:

Q: If the log will slide when a force of 443Ib is applied horizontally, what is the maximum angle the…

A: Introduction In this problem, we will calculate the greatest angle that the force that can be…

Q: Question 2 Find the value of The reaction force at the support A. (X,XX,XXX represents the last…

A:

Q: O AEd It vec B, = N Submit Request Answer Part E- Part E There exists a point of zero shear between…

A:

Q: Two forces are applied to a rod as shown below and the rod is in rotational equilibrium. The axis of…

A: The given information in the problem is shown in the following attached image:

Q: vonne is pulling on the doorknob of her dorm door to keep it closed while Joyce is pulling from the…

A: a)Torque is force applied at a distance from some central point (here it is the door hinge)we know…

Q: Determine the magnitude of the pin reaction at A and the magnitude and direction of the force…

A: Given Data All dimentions are modified into the 1.1 m The mass of the object is modified into 175 kg…

Q: The hoist supports the 125-kg engine (Figure 1). Figure G -1 m - F -2 m 2 m H 1m- 1 of 1 E 2 m 1 m…

A: The hoist supports the 125-kg engine (Figure 1).Determine magnitude of the force the load creates in…

Q: F E 3 ft A C В 4 ft 4 ft 800 lb

A:

Q: If a 200 N force F1 is applied to the piston with the 4 cm diameter, what is the magnitude of the…

A: Given data:find:Force resisted by piston F2

Q: 4 different questions please provide all steps for each and units

A: A.) Apply method of joint at F to get the force member CF since the allowable number of unknowns for…

Q: The nail cutter consists of the handle and the two cutting blades (Eigure 1) Figure 6 mm 6 mm -36 mm…

A: According to the given data F=6 N We need to find Force on the fingernail by the cutter

Q: Question 4 Part A If 0 = 27° and F = 5 kN , determine the magnitude of the resultant force acting on…

A: Given -

Q: The following forces are acting on the bracket below (a free-body diagram of the bracket is shown),…

A: Given data: The magnitude of the force F2 = 62 lbf. The horizontal distance between points 1 and 3…

Q: A block sits on a plane, and there is friction between the block and the plane. The plane is…

A: Graphical representation of forces may be applied externally, reactions ( normal force, tension,…

Q: The hydraulic crane is used to lift the 1380-lb load. Determine the force in the hydraulic cylinder…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.