what is the length of the red line?

Q: What is the low limit on the smallest outside diameter?

A: Solution:

Q: H. What scale is used if a line 84 mm long represents a fence 63 m long?

A: Given:-  Scale length = 84 mm Actual length = 63 m = 63000 mm  To Find:-  Scale

Q: re 2) mine the smallest allowable diameter of the roc able bending stress is allow = 225 MPa.

A: Apply the moment equilibrium condition about point A.The force equilibrium condition along the…

Q: complete the missing lines in the figure below 8.

A:

Q: If 17 welders can complete a job in 134 hours, how long will it take for 21 welders to do the same…

A:

Q: Choose one of the following statements which is not true.

A: for solution refer below images.

Q: where are the graphs?

A: Given data in the related question: Maximum speed = vf = 183.58 mi/hr Distance travelled = 5 mi Time…

Q: Please make draw the right-side view, front view, and top view of the given isometric drawing.…

A:

Q: 300 mm 30º 300 mm 300 mm Can someone please label the projection of F and the rest of the…

A:

Q: 400 300 stn 60

A: 400sinθ=500sin60=5003/2=10001.732=578.03

Q: The first moment of an area (mm3) about the x-axis (Qx) is O 462,000 O 594,000 O 246,000 864,000

A:

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: pr... below. 5) Sketch the appropriate sectional view on the front view of the part

A: Given:To find:Sectional view on the front view.

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: Given the front, top and side views of the drawing add the missing lines (center, object, and…

A:

Q: At the instant the hand has stopped pushing, the tangential acceleration of the ruler is Group of…

A: Let the torque applied by hands be And the length of the ruler be The tangential acceleration can be…

Q: What unit is the 0.000931 ?

A: Torsion equation is given by, TJ=τr=GθLwhere,T = torque acting or applied in N-m or N-mmJ = polar…

Q: What is the basic unit for length?

A: Solution Length → The measurement of something from end to end is called length

Q: how did you find d1 and d2

A: This question is based on the concept of polar radius.

Q: What type of lines can be used in a drawing to show that part of an object has been removed ?

A: Solution : There are two types of line which are used to show the removed part of an object : Break…

Q: Q.1) Knowing that the tension in cable BA is 570 N, determine the moment about O. Neglect the…

A:

Q: The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from…

A:

Q: The thin plate with four holes as shown in Figure 6 has a mass per unit area of 33 kg/m². The radius…

A:

Q: what is the bottom length?

A: To calculate the bottom length

Q: question: The degrees of freedom of the calculation package in the figure?

A:

Q: Compute the deflection of C after the load removed.

A: Given Conditions :

Q: Number of links? The value must be a number 8 Number of full joints (J1)? Figure 2 Figure 2

A: Given mechanisms,

Q: is the welding process in which two pieces to be joined are overlapped and placed between two…

A:

Q: 14 sketch in the missing object and ce nter lines on 14

A: Given figure  To sketch the missing lines  And hidden lines

Q: Draw an orthographic(three-view drawing) of the four objects including front, top, and right views

A:

Q: Z is incorrect

A:

Q: if the bullet that hit the cashier made a bullet hole that was 3 mm wide and 8 mm long, white was…

A: Given data:

Q: What is the radius equivalent to Mohrs Circle?

A: Method to construct Mohr's circle, First Plot point A σx,-τxy, & B σy,τxy on σ - τ plane. Now…

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: Is this for number 1 only?

A:

Q: Interpret the significance of the letters shown in the illustration

A: Instruction given at tail of the welding symbol is "See detail A".Here detail A will have the…

Q: C O C

A: Given: Hatching: Differentiates the areas that are cut and those areas that are not cut by the…

Q: i need to know what each number means in the diagram.

A:

Q: True or False? All rectangular x-sections less than 12-inch in width and less than 0.23-inch in…

A: The minimum width for the all rectangular section to be known as strip is 12 inches while the…

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.