What is the gauge pressure inside the tank in kPa?

Q: 4. If the Pressure at A- 135 kPa, what is the length L? P 1000 kg/m, Pmercury 13545 kg/m 32 cm 18 cm…

A:

Q: If a closed tank contains compressed air and oil (SGoil = 0.90), with a U-tube manometer using…

A:

Q: A 0.625" OD x 0.035" Wall x 0.561" ID Copper Round Tube is being used in a pressure system that is…

A:

Q: Determine the hydrostatic force and its location by (a)integration method and (b)formula method. 3m…

A:

Q: a. For U-tube manometer shown in the figure (a), fluid 1 is water and the gage fluid is mercury.…

A: As per the guidelines, I can solve only one question at a time and I can solve only first question.…

Q: A cylindrical tank is constructed with hemispherical heads. The tank diameter is 1.32 m, the wall…

A: Givend=1.32mt=20mm=0.02mP=1.560kPa

Q: Resultant = 1028 x 10 Ibf acts along z- 10.083 – 0.5555x 3.75 ft Fy= 499 x 10' bf F-899 x 10' Ibr `…

A: The values highlighted in the image are derived from coordinates of points where the resultant force…

Q: Consider the gate shown in (Figure 1). The gate has a width of 2 m. pw = 1.0 Mg/m³. Suppose that a =…

A: Given: The width of gate is is w=2 m. The density of water is ρw=1.0 Mg/m3. The value of a=2 m, b=2…

Q: The 600-lb, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making…

A: Լուծում;

Q: A strain gauge measured the hoop stress on the surface of the tank as 291,989 Pa. The tank diameter…

A: Given The value of the hoop stress for the cylindrical tank is σh=291,989 Pa. The diameter of the…

Q: 2. A vertical square surface as shown in the figure as shown in the figure has its upper edge…

A:

Q: In Bourdon Gauge experiment, if the mass of the piston is 340 gr and mass of the platform is 173 gr,…

A:

Q: A cylindrical steel tank having an internal diameter of 50 in. is submerged in seawater (weight…

A: Given: The diameter of tank, d = 50 in The weight density, ρg = 64 lb/ft^3 The depth, h = 9750 ft…

Q: a cylindrical pressure vesssel( diameter =2.8m and wall thickness of 35mm) is made of steel. the…

A:

Q: a cylindrical pressure vesssel( diameter =2.8m and wall thickness of 35mm) is made of steel. the…

A:

Q: What is the practical importance to measure the hydrostatic power?. e 2:18 /

A: Hydrostatic power,  it is basically a hydraulic system where the hydraulic pump or an accumulator…

Q: A tank 12 m high and 2 m in diameter is 15 mm thick. The max tangential stress is ? The max…

A: To Find : The maximum tangential stress.The maximum longitudinal stress.Given : The diameter of…

Q: Determine the hydrostatic force and its location by (a)integration method and (b)formula method. 3m…

A:

Q: If a spherical balloon is made of an inelastic material that can withstand 395 KN before bursting,…

A:

Q: Neglecting losses, determine the x- and y-components of force needed to hold the tee (Fig. 3.63) in…

A: At 1-

Q: Determine the gage reading P in psi. SG of Hg is 13.57. Show your work

A:

Q: bulk modulus c

A: To find Bulk modulus of elasticity of oil

Q: A WATER TANK IS “L1” IN DIAMETER AND “L2” HIGH. IF THE TANK IS TO BE COMPLETELY FILLED, DETERMINE…

A:

Q: w t Please write in clear handwriting a onaration 3. Problem: Detemine the gauge pressure pm at the…

A:

Q: Caleulate the force F required to Keep the paraboli gate in static equilibrium shown in the Fiqure.…

A: given; a=8.8mb=4.8mwidth(w)=2mspecific gravity (SG)=8.4

Q: The wall thickness of a 1.0 ft diameter spherical tank is 1.0 inch. Calculate the allowable internal…

A: According to the given dataD=1 ft=12 int=1inWe need to findInternal pressure

Q: Three liquids of different densities fill connected tubes as shown in the figure below (not drawn to…

A:

Q: A water tank, 22 ft in diameter, is made from steel plates that are ½ in. thick. The circumferential…

A:

Q: Parameter Unit (a) FTOTAL (b) T1 (c) T2 (d) 01 (e) o2 Ib Ib Ib psi psi elele

A: Given: D= 6 ft H=12 ft h=9 ft sg=1.5 density=1500 kg/m^3=93.64 lb/ft^3 A=0.5 in^2 TO determine: The…

Q: Solve for the hydrostatic force per meter length acting on the radial tainter as shown in the…

A:

Q: Q1. (A) Explain the function of inclined manometer, burden gauge, and inverted manometer?

A: Manometer: It is a instrument which is used to measure fluid pressure. It have a tube filled with a…

Q: A trapezoidal plate shown in the figure is submerged in water is 3.3 m below the surface. The bases…

A: Givenh=3.3mb1=3mb2=8md=10mγ=9.75 kN/m3

Q: Air, 32kPa 1m Oil, SG=0.8 blem 4 Determine the magnitude and location (take the measurement using…

A:

Q: Find h when the pressure in tank B is 21 kPa.

A: Given data: -  The pressure in tank B is PB = 21 kPa. The specific gravity of oil is SGoil = 0.91.…

Q: a cylindrical pressure vesssel( diameter =2.8m and wall thickness of 35mm) is made of steel. the…

A:

Q: Consider the (Figure 1). Figure FR = Submit B Value -1.5 m Determine the magnitude of the…

A: Density of water= 1Mg/m^3Width of gate = 1.1 mFind the magnitude of force on the gate

Q: A 27 m vertical column of fluid (density 1878 kg.m3 ) is located where g= 9.65 m/sec2 .  Find the…

A:

Q: Q2: In Figure below, the gauge pressure, G reads (- 2.0) Psi and gate AB has a height of 6 ft and…

A: Given: Gauge pressure=-2psi or -13789.5Pa height of the water=18ft or 5.4864m height of the…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.