What is the gauge pressure at Point G in the figure below (Patm= 101.3kPa). Open to atmosphere Closed top 1m Plan view (view E-E) Open to atmosphere 1'0m 2 m- 1.0m Air 1.5m Air 2.0 m S=2 2.0 m Water G Elevation view O a. 169.97 kPa O b. 88.29kPa O . 189.59 kPa O d. None of the mentioned O e. 68.67 kPa

Q: The dot product of two unit vectors: (The answer cannot be found on the other choices.) always has a…

A: When the dot product of any two vectors is equals to 1 then those vectors are in same direction…

Q: (Determine the (f_y ) when force 80 Ib and angle 30° on the axis (X .A 40 .B 40lb .C 4lb .D 40N

A:

Q: X 300 mm D 800 mm B

A:

Q: The region bounded by the parabola x = y² and y = x2 revolved about the y-axis to generate a solid.…

A:

Q: PO 8 in.

A: Redraw the following figure for the given question.

Q: Q3/ For the plate shown in figure below find (a) E A Y수 4 6 X 7 5

A: Let us consider the given figure , divide into two parts of area A1 and A2 The sum of area ΣA can be…

Q: If Ma- 68.5 kN-m and Mc- 56.0 kN-m, use the graphical method to construct the bending -moment…

A:

Q: h a 60° 60° --X

A: Let’s divide the shaded area into two parts. Section 1 is a triangle OAB and Section 2 is a circular…

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 2 m Find the angle theta. a = 5. b = 3. 1m 1m D

A:

Q: In the picture, a weight pulls on a pulley (solid disk) of mass 0.5kg and a radius of 0.25m. The…

A:

Q: X 300 mm D 800 mm B

A: For constant angular velocity, angular acceleration is zero,

Q: Determine all furce mem bers of truss Shown the

A:

Q: Find The curevature points A,B,C,D form least to greatest

A:

Q: The landing gear system of a plane is made of an actuator AC and 2 rods CB and OAB. They are pin…

A:

Q: The mass of casting is 120kg after 6% of its mass was machined off. Determine the mass of the…

A: The mass of casting is 120kg after 6% of its mass was machined off. Determine the mass of the…

Q: 400 Ib 14' A 60° 450 Determine the Value of P

A: given data: let  RA=normal reaction force at ARB=normal reaction force at B AC=4' CD=14' DB=2'

Q: The engine piston weighs 180 g. The machine speed is 4400 RPM. What is the maximum speed of the…

A:

Q: Determine the x-y and n-t components of the 39-kip force F acting on the simply-supported beam. F =…

A:

Q: determine (a) the required value of a if the wn is to be vertical, (b) the corresponding 30° 200 N

A:

Q: Determine the angle 0 between the edges of the sheet-metal bracket. -400 mm 250 mm 300 mm 50 mm y

A:

Q: Fint total force acting on point A. Point A can be anywhere.

A:

Q: Part A In Eigure ). w35 kip/ft. Folow the sign convention Delermine the shear force acting at point…

A:

Q: Fy = 16 kN O Fy = 4 kN O Fy = 2 kN O

A:

Q: For the rotational system shown in the fig- ure, write the equations of motion from which the…

A:

Q: Express the quantity 254,998m in mm.

A: To convert meter quantity into millimeter one must be familiar with the no. of mm exist in one…

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A:

Q: In order to pull out the nail at B, the force F exerted on the handle of the hammer must produce a…

A: According to the question data MA=200lb.inclockwise   and the figure  We need to find Force F to…

Q: What is the direction of the edge formed between the intersection of (211) and (102)?

A:

Q: Find the center of gravity of the wire.

A: The centroid, when referring to a solid item, denotes the geometric center or the location where the…

Q: Dotermine ali force truss Shown mem bers of thhe

A:

Q: Find the angle between the planes x + y = 1 and 2x + y -2z = 2

A: Write the expression to determine the normal vector of both the planes. Substitute the value of…

Q: A hollow tube with thickness t = 1/4 in. is applied with a tensile load of 33 kips. Compute its…

A: Given data,  Tensile load P= 33kips = 33000 lbs  t= 1/4 in  Tensile stress S= 12 ksi = 12000 lb/in²…

Q: Express:            50000mm3 as m3 3.5m3 as mm3 20m3 as cm3 45cm3

A:

Q: +y (i) +5 dx y cosx dx dy dx (m) dx (iv) dx

A: Degree & Order: Order: highest numbered derivative in the equation Degree: highest power to…

Q: Determine the moment of 75 N force about point B in the figure shown below. 160 mm D a- 120 mm B 250…

A:

Q: Solve erf only

A: Given:To Find: the value of x.Note: In the above equation,

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.