What is the frictional hp acting on a collar loaded with 100 kg weight? The collar has an outside  diameter of 100 mm and an internal diameter of 40 mm. The collar rotates at 1,000 rpm and the  coefficient of friction between the collar and the pivot surface is 0.15.

Q: A 2.88 m long ladder that has a mass of 5.49 kg leans against a vertical frictionless wall. The…

A:

Q: An elevator type lift is being designed to raise a load up to 5,000pounds between floors. Two…

A: Load to be raised : 5000 pounds Diameter of the screw threads 1.5 in Weight of the elevator is 800…

Q: 3. A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and…

A: Given data: - The speed of the belt is v = 1440 m/min. The friction coefficient between belt and…

Q: A box of mass m = 30 kg is at rest on a ramp inclinedat 50° to the horizontal. The coefficients of…

A:

Q: The box shown in the figure has a weight of 250 pounds. The coefficient of static friction between…

A:

Q: A slider crank mechanism operates at 5 m/s and applies a force of 40 N to the slider. The slider…

A: Given:- Force= 40N Velocity of slider= 5 m/s Slider weight= 3 kg Slider Dimension:= 0.6 x 0.2m

Q: Please don't provide handwritten solution .....

A: Given -  Explanation - Image -1 Image -2 Hope you Understand. If any Query let me know.  Thank You.…

Q: The tension in a pulley belt is 300 N when stationary. The smaller pulley has a diameter of 300 mm…

A:

Q: A horizontal force of P = 100 N is just sufficient to hold the crate from sliding down the plane,…

A:

Q: The coefficient of kinetic friction between the 30-mm- diameter pin and the pulley is 0.25.…

A: (a) To find: The tension required to raise the load. Given: The radius of the pin is r=15 mm. The…

Q: A body of weight 8 newton is placed on a rough plane inclined to the horizontal at angle 6. A force…

A: Given data: Weight of the body, W = 8 N. Draw the free-body diagram of the body. Apply…

Q: solve show solution

A:

Q: A box of mass 100 kg is placed on a 30 degrees inclined plane. The applied horizontal force is 100 N…

A:

Q: A bicycle and rider travelling at 15 km/hr on a level road, have a mass of 100 kg. The brake is…

A: Write the given information.

Q: An 90.17 kg person is half way up a uniform ladder of length 3.939 m and mass 29.49 kg that is…

A: Here we will apply equilibrium conditions.

Q: PROBLEM 1 10 ft c platform B ramp 45⁰ 4 ft Data: The box a point A has a weight of 80 lbs. The box…

A: Given: The weight of point A, W = 80 lb The initial speed of the box, u = 8 ft/s The coefficient of…

Q: Friction problem: Two packages are placed on a conveyor belt which is at rest. Between the belt and…

A:

Q: A string passes over the top of a fixed cylinder of radius R = 10 cm. One end of the string is…

A:

Q: The 54-kg block rests on the horizontal surface, and a force P-342 N, whose direction can be varied,…

A: The given information in the problem is represented in the following attached image:

Q: The crate has a weight of 490 lb and a center of gravity at G rests on the floor for which the…

A: Let m = Mass of crate =490lb = 221.97kg g= Acceleration due to gravity =10m/s2 W = Weight of crate…

Q: Consider the centrifugal clutch above that comprises of four ‘shoes’ symmetrically attached to the…

A: The mass of each shoe is The spring stiffness is The coefficient of friction is The radius is To…

Q: The tension in a pulley belt is 300 N when stationary. The smaller pulley has a diameter of 300 mm…

A: Introduction In this problem, we will calculate the tension on each side of the belt and the power…

Q: A screw of the type indicated below is used to apply a force to the wedge, which then moves the…

A: The mass of the block is calculated as,m=500 kg The coefficient of static friction,μ=0.2 The…

Q: A pulley consists of a 120-mm-diameter wheel that fits loosely over an 18-mm-diameter shaft as shown…

A: Given: M=2.5 kgWeight of pulley is 5 N.r1=182=9 mmr2=1202=60 mm The free-body diagram of the pulley…

Q: A car engine has its rated output of 16 kW. The 2 maximum torque developed is 120 N-m. The clutch…

A: Given data as per the question power of car engine =16 kwMaximum torque developed =120 N.maxial…

Q: Two blocks A and B have a weight of 50 N and 40 N, respectively. They are resting on the incline for…

A: (a) Draw a free body diagram for the problem. Here, Fs is the spring force, FA is the frictional…

Q: Don't Use Chat GPT Will Upvote

A: Part (a): Free Body Diagrams Let's draw the free body diagrams for each box: Larger Box (M):Weight…

Q: -. A body having a mass of 40 kg rests on a horizontal table and it is found that the least…

A:

Q: High-strength bolts are used in the construction of many steel structures. For nominal-diameter…

A: Given, Tension T = 51 kips Mean diameter d = 0.94 in lead L = 0.125 in Coefficient of friction μ =…

Q: el ramp is used by a worker in a factory to move a cardboard box. The box weighs 40 lb with a center…

A: Given:W=mg= 40 lbμ=0.3NOTE: According to Bartleyby's policy we shall answer only three sub-parts so…

Q: 5-9. The ladder of Fig. P 5-9 weighs 60 lb, and its center of gravity is at the mid-point. The…

A: Given:Wl=60 lbW=150 lbμA=0.3μB=0.1

Q: A bicycle and rider, travelling at 12 km/hr on a level road, have a mass of 105 kg. A brake  is…

A: Write the given values with the suitable variables. u=12 km/hr=12×10003600 m/s=3.33 m/sm=105 kgd=800…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.