What is the force in member IJ?

Q: What is the minimum tension must your cable be able to support without having your sign come…

A: Given data: - The length of the beam is L = 1.60 m. The mass of the beam is m = 20 kg. The mass of…

Q: A pair of forces when applied to an object decreases its length in the direction of the forces are…

A: A pair of forces when applied to an object decreases its length in the direction of the forces are…

Q: rite classification of force system and explain any one in Detail.

A: given; Write classification of force system and explain any one in Detail.

Q: what is the minnimum proof strength mpa for M14x2 hex bolt

A:

Q: the bending endurance limit for AISI 1080 steel shaft is Select one: a. 307.5 MPa. b. 250 Мра с. 450…

A: The bending endurance limit for AISI 1080 steel shaft can be given by - Se = 0.5×Ultimate strengthSe…

Q: Prepare a preliminary design review for a new motorcycle jacket development.

A: Many countries require the use of personal protection equipment, such as protective clothes and…

Q: onsidered as d

A: given: Describe the nature of force vibrations why their considered as destructive.

Q: Due to imperfections in manufacturing or specific applicationof the load, a column will never…

A: Under the application of axial load over a column when there is a deflection in the lateral…

Q: An example of a performance with two phases is the bench press; in the down phase the lifter lowers…

A: The preparation phase and the movement phase of the bench press exercise can be separated.…

Q: What additional force A is needed to keep the block in static equi

A: The calculated additional force is needed to keep the block in static equilibrium.

Q: what is true in the lever arm below? a. it is unstable b. statically determinate but unstable c.…

A:

Q: Identify the zero force members (if any) in 3 kip H. 2 kip T. 8 ft 3 kip -1.5 kip- 4 ft |B C ID -10…

A:

Q: ommendation, what is the factor of safety for a key under seve

A: Ans: The factor of safety is taken as 3 to 4 for key design under difficult situations.

Q: 5 ft 2 ft 7 ft The train has a weight of 23000 Ib and a center of gravity at G. It is suspended from…

A: Free Body Diagram for the given condition can be made as shown below: All normal reactions are…

Q: Customary units to SI units by using the values listed for length and force as defined values:…

A: Distributed load is equal to load(force) acting per unit length of any member.

Q: Universal joint is used for non parallel shafts whose axes are O coplanar. connecting radiator…

A: Universal joint: The universal joint is a joint between two rotating shafts which allows to move the…

Q: What is load and extension

A: Load is basically a force which is exerted on a body or a surface due to which there may be some…

Q: What happens if the load on an actual column exceeds its critical loading?

A: There are two types of the column, 1. Short Column 2. Long Column The slenderness ratio and length…

Q: QUESTION 10 A load of 6kN is supported as shown in the figure. The weight of the pulley is 2kN.…

A:

Q: Which of the following materials combinations are most likely to fail due to excessive wear in the…

A: 316L Stainless Steel Ultra High Molecular Weight Polyethylene is most likely to fail due to…

Q: Given a distributed load, how do we find the location of the equivalent concentrated force?

A: Given a distributed loadfind out:how do we find the location of the equivalent concentrated force

Q: List four possible causes of cluth slippage

A: A Clutch is a mechanical device used in vehicles that transmits power from the motor to the…

Q: Materials that can be used as housing for the Wedge belt Drive

A: The materials used are -

Q: Define eccentric impact.

A: Eccentric impact:- If the line of the impact of bodies doesn't coincide with the line connecting the…

Q: What happens when the member is confined?

A: Confined member: If a member is confined then it means it is fixed to a position.

Q: muscles 1. State the class of lever of each device below. load force fulcrum Туре2 Туре? Туре? Туре?

A:

Q: Briefly explain the load torque and applied torque with reference to the physical demonstration…

A: The load torque and applied torque are explained as under,

Q: What is the maximum deflection?

A: Given Beam To find Definition of maximum deflection

Q: Define Braking loads

A: Braking load/force  is the  frictional force that cats tangentially  between the brake pads and…

Q: upler alve cumulator Main body -Housing -Back head -Impact piston Chisel

A:

Q: Describe how to test for equilibrium of masses ?

A: Let us discuss about  equilibrium of masses and criteria when it is in equilibrium condition.

Q: What is the part of the sprung weight of a vehicle?

A:

Q: What basic calculations would be made to verify the general problem statement: "lift cylinder…

A:

Q: Which of the following is not used in this support reaction experiment? Select one: Scale Vernier…

A: Which of the following is not used in this support reaction experiment

Q: Should torsion be considered? Torsion must be considered if T, exceeds the threshold torque given by…

A: Given Torsion  To find To satisfy the factored torsional moment

Q: or how long is the load naintained in a Brinell est__----_? O a. 10 seconds O b. 15 seconds O C. 20…

A: In this process maintain constant load condition. so time is major role in the test

Q: What is unit of Force in british system(UK).

A: Given Data Force

Q: What forces exist in series spring systems?

A:

Q: What is the force resisted by member BC? 30 kips 30 kips A 8 ft B 8 ft C &8 ft D E 18 ft G Select…

A:

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.