What is the equivalent stiffness?

Q: What is section modulus?

A: The section modulus helps to calculate the outermost stress in the beam section. It is numerically…

Q: What is the measure of the stiffness of a volume of material?

A: What is the measures the stiffness of volume of material..??

Q: Give an example of a flexure formula?

A: The flexure formula is also known as the flexure bending equation and is defined as; Where, M is…

Q: What happens if the principal stresses at a critical point in the material?

A: First, define the critical point. Critical points are those points in the given plane where the…

Q: What thickness limit classifies metal as being sheet?

A:

Q: What is the effect of an eccentric loading?

A: Eccentric loading: The eccentric loading is a type of loading on beams and columns in which load…

Q: What is the slenderness ratio?

A:

Q: What is creep strength?

A: Creep is the phenomena of deformation of a body which is time-dependent. It occurs when a load is…

Q: What is the tensile stress?

A: When there is loading over a member in the direction of its axis, then stress produced under such…

Q: What is the Average Compressive Stress?

A: Forces acting perpendicular to the cross section of the body are normal forces. They can be either…

Q: On what is the Design of a member for strength-based?

A: The strength-based design approach is a type of design where our main focus is on strength of…

Q: How are the Normal and Shear Stress Components used?

A: Normal stress is defined as stress which induced due to the outside force acting normally on a…

Q: What is true stress and true strain?

A: To define: True stress True strain Stress: It is defined as the internal resistance developed at a…

Q: Mention the main advantage of Vickers hardness test method? ...... ............ ....................…

A: Vickers hardness test method - it is a optically hardness test to measure the hardness of material,…

Q: What is maximum deformation?

A: Given Deformation To find Maximum deformation

Q: What are the three equations of flexural rigidity?

A: Flexural Rigidity  It defined as the resistance offered by structure while undergoing bending or it…

Q: What are the ultimate strengths in tension and in Compression for ASTM A48 Grade 40 cast iron?

A: Given data  What is the ultimate strength in tension and compression for ASTM A48 Grade 40

Q: 4. What useful informations are obtained from the tensile test of a ductile material? 5. What do you…

A: 4.What useful informations are obtained from the tensile test of a ductile material?       Note :-…

Q: With what is Stress associated and how?

A: Please Specify the question in more detail, sir.   But in general, it can…

Q: How did temperature affect the toughness of the specimens?

A: temperature affecting the strengths of the toughness . IMPACT TOUGHNESS        Toughness is the area…

Q: What 3 types of loading may lead to failure?

A: There are various ways by which a material may lead to failure. For instance, in case of mechanical…

Q: What happens when the material is stressed beyond the yield point?

A: Any material is subjected to various processes and follows a stress-strain curve. In this curve,…

Q: what is the rate of deformation?

A:

Q: What are the tensile forces?

A: Tensile force is the force applied on a material which stretches the material. The tensile force…

Q: What are the various stresses induced in the wire rope?

A: Wire rope is made of metal and twisted in the form of a helix. The wire rope consists of several…

Q: why specific rigidity is needed?

A: Specific rigidity is defined by the ratio of young's modulas to the density. The more accurate term…

Q: What is the modulus of rigidity?

A: Modulus of rigidity

Q: unit of shear strain

A:

Q: What is the "flexure formula?" along with what are the units for the flexture formula as well as the…

A: Given data  What is the "flexure formula.