What is the compressive stress ?/?on a woman's feet, in units of kilopascals (kPa) , if the woman's weight is spread out evenly over both soles of her shoes? Assume her mass is 64.0 kg and each shoe has an area of 220.0 cm2. ?/?=   kPa

Q: 0.25 in. 5 in. 1 in. 0.25 in. -0.25 in. 2.5 in.

A: Maximum axial force P that can be applied to the steel plate

Q: The total cross-sectional area of the load-bearing calcified portion of the two forearm bones…

A: Cross-sectional area is Initial velocity is Final velocity is Time is Mass is Note:Find:The…

Q: 6. A 40.0 m long steel elevator cable has a cross-sectional area of 4.0×10^(-4) m^2 and is able to…

A:

Q: essive strength of 140 MPa. a) What is the effective cross-sectional area of the femur in a human?…

A:

Q: In regions of the cardiovascular system where there is steady laminar blood flow, the shear stress…

A:

Q: The maximum height h of a mountain depends on the density of the rock the mountain is made out of ?ρ…

A:

Q: The total cross-sectional area of the load-bearing calcified portion of the two forearm bones…

A: Given that -  Mass Velocity Cross sectional area To Find - We have to determine the required…

Q: A cable hanging vertically under gravity must support its weight, w = mg, where m is the mass of the…

A: To avoid snapping of the cable, the tensile strength will be equal to the force per unit area. Write…

Q: A steel rod 55 cm long has a diameter of 35.0 cm. The compressive strength (the maximum stress it…

A:

Q: 2. The breaking stress of copper is 210 MPa. What is the maximum force that can be applied to a…

A: Given, Breaking the stress of copper, σb=210MPaσb=210×106Pa Diameter, d=1mmd=1×10-3m The braking…

Q: A 35.0 kg mass hangs from a steel wire. The unloaded length of the wire is 3.05 m and it has a…

A: Mass hanging from steel wire,                     Initial length of an steel wire,…

Q: 1. This graph is a stress-strain diagram that is of the type often studied by mechanical engineers…

A: We need to find the physical meaning of the area under the stress-strain curve.

Q: A 210-kg load is hung on a wire of length of 3.30 m, cross-sectional area 2.00 x 10-5 m2, and…

A: mass of load (m) =210 kg initial length of Wire (L0) = 3.3 m Cross sectional area of Wire (A) = 2.0…

Q: Young's modulus for compression of human bone is approximately 9x10⁹ N/m^2. Assume that a femur has…

A: Given in question :  Young's modulus (Y) = 9 x 109 N/m2  Stress (S) = 7.5 x 107 N/m2  Length of the…

Q: A cable used to lift heavy materials can resist breaking even under a load of 1 meganewtons. The…

A:

Q: Problem 4: Suppose a piano tuner stretches a steel piano wire 5.5 mm. The wire was originally 0.95…

A:

Q: hear stre steel plat rivets and

A:

Q: Steel beams are used for load bearing supports in a building. Each beam is 4.0 m long with a…

A:

Q: A steel wire of length 2.10 m with circular cross section must stretch no more than 0.300 cm when a…

A:

Q: A rectangular timber tie 180 mm x 80 mm is reinforced by a bar of aluminium of 25 mm diameter.…

A: A rectangular timber tie 180 mm x 80 mm is reinforced by a bar of aluminium of 25 mm diameter.…

Q: 2. Let's look at the femur – the largest, longest, and strongest bone of the human skeleton. Let's…

A:

Q: The total cross-sectional area of the load-bearing calciried portion or the slammed against the…

A:

Q: of the stud is under compression, and which surface is under tensi op and bottom surfaces are under…

A: The bending can be shown as,

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).