what is the angle in red?

Q: can you do it in polygon

A: Given vectors : A :  2 kph 45°N of E B :  2.8  kph 58°E of S C :  5.1  kph 28°W of S D : 3.2  kph…

Q: why does the highlighted parts become 0?

A: Given Data: ∬CST→ dA+∭CVB→ρ dV=∂∂t∭CVV→ (ρ dV)+∬CSV→(ρV→.dA→) dA Neglect friction and gravitational…

Q: is it correct?If this is correct, please help me to see the red line which has a question mark.…

A: For Velocity ratio:=0To determine:Velocity ratio for optimum performance of wind turbine.

Q: How many auxiliary views are found on this print?

A: Some objects are too complex that do not show the best geometry of the part by three principle view.…

Q: A uniform disc of diameter 300 mm and mass of 5 kg is mounted on one end of an arm of length 600 mm.…

A:

Q: what is the length of the red line?

A: Solution:

Q: What is the sketch of the right face

A:

Q: A double-thread worm has a pitch diameter of 3 inches. The wheel has 20 teeth and a pitch diameter…

A:

Q: Please make draw the right-side view, front view, and top view of the given isometric drawing.…

A:

Q: Determine the magnitude of the pin force at A. Assume W - 875 lb, a = 2.9 ft, b-2.4 ft, r - 6 in. I'…

A:

Q: is it correct?If this is correct, please help me to see the red line or red circle which has the…

A:

Q: Ø60 60 R15 18 120 36 14 Dimensions are in mm 18 18 24

A: In third angle top will be above the front view.

Q: 59. A mass m is mounted betwe two springs with constants k, and k2, as shown in Fig. 13.32. Show…

A: As per the policy of the bartleby I can answer 1st question only. All the questions are different to…

Q: 3. FBD for AK to determine the internal forces on K: forces/reactions on the AK; a. There are b. Sum…

A: In this problem, it is asking for question (3) so we will provide the solution for question (3)…

Q: 38 Hole Tam delik 20 20 26, 09

A: Given 3D Part:

Q: Can you draw the OBLIQUE SECTION VIEW of this figure?

A:

Q: A mass of flexible machine part, m, of of 10 Hz. The vibration was caused by the application of a…

A:

Q: Draw the top view, side view, and front view of the figure below.

A: The required Front view , Top view and Side are drawn using third angle method of projection.

Q: the isometric drawing has to be in 30 degree angle or vertical

A: It is asked to describe whether the isometric drawing has to be at 30 degree angle or vertical

Q: Why cos(60 if I don't see that angle in the figure

A: This question can be solved by labelling angles.

Q: Draw an orthographic(three-view drawing) of the four objects including front, top, and right views

A:

Q: Draw the isometric drawing

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: draw missing view?

A: Given data: - The upper part of the given figure is the front view of the component. The lower part…

Q: Replace the loading by an equivalent resultant force. Suppose that wi = 3 kN/m and wz = 5.5 kN/m.…

A:

Q: 2. Rankine Cycle. Consider a steam power plant operating on the simple ideal Rankine cycle. Steam…

A: State 1: Pump inlet or condenser exit as saturated liquid at P1= 50 kPa State 2: Pump outlet or…

Q: C O C

A: Given: Hatching: Differentiates the areas that are cut and those areas that are not cut by the…

Q: For the objects shown in orthographic projection below, construct an isometric Use the box method to…

A: Find Isometric view of the object.

Q: c) Calculate the new stress ratio R, the stress amplitude o, in MPa and the mean stress o in MPa.…

A: In this problem, it is asking the answers for parts (c) and (d). (c) Write the given data. σmin=-132…

Q: 13. A 6.800-kg bowling ball sits upon a dolly of negligible mass and wheel-friction, and is attached…

A: Given data  mass of bowling ball (m) = 6.8 kg  spring constant (k) = 454 N/m  at t = 0 x = 9.88 cm v…

Q: o. Can you draw the ALIGNED SECTION VIEW and the OBLIQUE SECTION VIEW of this figure? I don't need a…

A:

Q: L HRP FRP (TOP VIEW) (FRONT VIEW) L (RIGHT SIDE VIEW) L

A:

Q: STATICS AND STENGITH OF MATERIALS Question: Express force Fas a Cartesian vector, then determine its…

A: Given: F = 600 lb a = 1.5 ft b = 5 ft c= 3 ft theta = 60 deg

Q: We begin with Direction A. (a) What is the x coordinate of the vector tail (x₁)? (b) What is the x…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: just answer number 40, thank you

A:

Q: What is the counterclockwise angle?

A: The counterclockwise angle is the angle measured in the opposite direction of the clock.

Q: A mass of flexible machine part, m¡ of 20 kg was observed to vibrate badly at frequency of 10 Hz.…

A:

Q: Hello. Can you draw the OFF SET SECTION VIEW and the OBLIQUE SECTION VIEW of this figure? I don't…

A: Given:- Engineering drawing of the part To find:- To draw the sectional view and oblique view

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.