Answered: What is the 8085 Assembly Language…

What is the 8085 Assembly Language Instruction That do the follwing The contents of a memory location, specified by a 16-bit address in the operand, are copied to the accumulator

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: a.Write the addressing modes of the following instructions: (i) MOV A, @R0 (ii) MOVX @DPTR, A (iii)…

A: The addressing modes of the following instructions are: MOV A, @R0 = Register Addressing Mode ( In…

Q: Pipelining in 8086 processors is achieved using which of the following option: O a. By using the…

A: Pipelining in 8086 is achieved by using BIU(Bus user interface). It fills the queue until the next…

Q: Explain with drawing Instruction set of PIC 16fxx Microcontroller List the Interrupt sources in…

A: We need to explain with the drawing instruction set of the PIC16fxx Microcontroller. We need to list…

Q: xplain the role of stack register in 8086 microprocessor. Subject is Introduction to Embedded…

A: Use of stack register in 8086 microprocessor :- A stack register is used to hold the information…

Q: Q11:design a two input logic circuit (A, B) to implement And, Or,Xor,Complement using Mux and logic…

A: As per company guidelines we are supposed to answer only one question. Kindly repost other questions…

Q: Please clearly. Write assembly instructions for an 8086 processers to add two hexadecimal numbers.…

A: Question: Write assembly instructions for an 8086 processers to add two hexadecimal numbers.…

Q: 6. Describe the operation of an OTE instruction.

A: OTE : This is a instruction which is used in the PLC . PLC : Programmable Logic Controllers.

Q: Given the 74LS147 Encoder TINKHK6206 Logic Symbol 56679AWN 74LS147 (a) What would be output if input…

Q: Explain how to find the physical address in a segment from the logical address for 8086…

A: The physical address plays a vital role to enable the data bus . it is also called as real address…

Q: a) Draw the figure for memory segments with 8086 microprocessor software model. Explain the logical…

A: There are 4 segments in 8086: 1) Code Segment (CS) 2) Data Segment (DS) 3) Stack Segment (SS) 4)…

Q: 1. Draw the figure showing the types of registers in an 8086 microprocessor. Write the register…

A: There are a total of five registers in an 8086 microprocessor. They are General purpose registers…

Q: Please circle whether following statements are True or false. (a) In Moore machines, more logic…

A: In this question we need to check the given statement is true or false

Q: The 8085-instruction set does not include a Clear Carry instruction. Which single- byte logical…

A: I'm this question we will write instruction of clear Carry flag...

Q: Draw the logic diagram and transistor implementation for a (2-2-2) AOI.

A: The logic diagram can be implemented as,

Q: a) Draw the Block diagram of Programmable Array Logic.

Q: 4- Design the logic circuit of 4-to16 decoder using basic logic gates. Find its truth table and…

A: The objective of this question is to design a 4-to-16 decoder using basic logic gates, find its…

Q: need the answer quickly

Q: 12. In which special function register is the bit RST a) PO b) ACC c) B d) PSW

A: The bit RS1 is located in the special function register called PSW which is called program status…

Q: Explain the function of Multiplexer and, Draw the 2 x 1 multiplexer logic circuit diagram and…

Q: st the disadvantages of Fixed function logic

Q: Briefly describe the following: a. Configurable logic blocks b. "Synthesis" process in FPGA c.…

A: From question d), Differentiate between reg and wire in verilog. There are Simple difference…

Q: A program written with the IDE for Arduino is called O a IDE source O b. Cryptography Oc Source code…

A: 1) Program written with the IDE for Arduino is called a sketch. This sketch is written in the text…

Q: Briefly describe the following: a. Configurable logic blocks b. "Synthesis" process in FPGA c.…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: A microprocessor is wired into a sensing control circuit so that the memory locations 80 and 81 each…

A: Aim:To write an assembly code for a microprocessor using MOV, JMP, and JNZ instructions, such that…

Q: number of logic gates present inside the 486 is two. ect one: True

Q: 10.Draw the logic symbal for a NOT gate and create its truth table.

Q: Draw a logic diagram of a divide-by-14 counter using IC 7493 and 2-input AND gate.

Q: Consider the following instruction breakdown that decomposes an instruction into 4 parts: OPCODE DST…

A: We need to find out number of bits for given statement ..

Q: A 8086 microprocessor perform the following ALU operation B9 H + E4 H. Draw the Flag Register and…

Q: You have a 16-bit timer and you want to configure it to generate an interrupt at a rate of 500 Hz.…

A: MSP430 is an ultra low power micro controller. It is a mixed signal processor with RISC…

Q: . Sketch v, for the network of Fig. 2.175 and determine the de voltage available. Ideal 170 V 2.2 k2…

A: In the given input voltage waveform, For positive pulse top left ideal diode is in OFF state, while…

Q: Design a three bit synchronous binary counter that counts two by two with T-flipflops,

A: Here you have two draw a three bit synchronous counter by using two flip-flops A). first draw…

Q: a) When does an E-MOSFET act as an open switch? b) When does an E-MOSFET act as a closed switch? c)…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

state the operation of the 2 of 3 logic controller and explain how it works
Describe any possible methods through which you can implement a RAM memory using logic gates?
An 8085 microprocessor executes "STA 1234H" with starting address location 1FFEH (STA copies the contents of the Accumulator to the 16-bit address location). While the instruction is fetched and executed, the sequence of values written at the address pins A15 - Ag is
1) In the mononstable multivibrator using 555 timer, if the output Q = logic (0), what will happen to the capacitor and the transistor? a) The capacitor will charge and the transistor will be OFF. b) The capacitor will charge and the transistor will be ON. c) The capacitor will discharge and the transistor will be OFF. d) The capacitor will discharge and the transistor will be ON
Draw the complete logic circuit using pic16f84a microcontroller and write the necessary code that generates the A, B, and C waveforms simultaneously and periodically. The circuit must include power supply, clock oscillator, and reset circuit with following specifications: instruction cycle is 1 microsecond with a high accuracy; Proper working supply voltage >= 4.5 volts. 6 ms 5 volts B
Write an assembly language program in microprocessor 8085 so that I can fetch 2 8 bit numbers from memory locations and store the product, whether it's 8 bit or 16 bit, in 2 different memory locations. I am aware with programming logic. So, only give me the working program and attach a snapshot of the output. No need to explain.
Use any digital logic simulator Fill-in the blank boxes with the correct LOGIC GATE/ Full/Half Adder
Solve last part 2(iv) Provide correct answer
Please do full and correct
Define a 2-bit demultiplexer to be a circuit whose single input line is steered to one of the four output linesdepending on the state of the two control lines (A, B). Draw its logic diagram (to the gate level) and specify the exactstate of A and B for each output line when that output line is selected.
Questions 2) Design an exclusive OR gate using a 2-to-1 MUX and an inverter.
Draw the logic circuit diagram. Don't give hand-drawn diagram