What are the phase current and phase voltage in a star connected load when this load connected to a delta power supply has a phase voltage 1100 V and a phase current of 37 A O 64 A, 1100 V O 32 A, 635 V 64 A, 635 V 32 A, 1100 V

What are the phase current and phase voltage in a star connected load when this load connected to a delta power supply has a phase voltage 1100 V and a phase current of 37 A O 64 A, 1100 V O 32 A, 635 V 64 A, 635 V 32 A, 1100 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: What is the maximum power transfer that can be made to ZL according to the values of the following…

A: V= 9.2 phase 80 VR= 8 OhmsL= j15 OhmsC1= -j19 OhmsC2= -j13 Ohms

Q: Calculate th Inductive reactance, the total resistance, and the impedance of the RL Parallel…

Q: For the circuit shown in figure below, Find the current Iz by using the loop (Mesh) method. 40 +j15…

Q: Ep Load = 927 V IL Secondary = 109.06 Ratio = 1:2.5 Z = 8.5 Ohms Find: EP Primary: ? Ep…

Q: Aplique análisis de mallas para hallar la corriente I. en el siguiente circuito.

A: a mesh is a loop that does not enclose other loops. KVL, states that “in any closed-loop network,…

Q: 3Ω j4Ω 2/0 A A =-j20 5Ω :-j22 65 ww

Q: R = 609 ohms L=0.57 mH C = 125 pF www R Calculate the following: a. XL and XC b. Total I and…

A: Given that Series RLC circuit. R = 609 ohms L = 0.57 mH C = 125 pf Vs = 120 v f = 60 Hz

Q: In series R-L circuit, R is 10 ohm and L is 20 mH. If the circuit current is 10sin(314t) A. The…

A: In series RL circuit, R=10 Ω, L=20 mH,it=10sin314t A.

Q: What is the scale in this diagram?

A: Given: Phasor diagram of a balanced delta load

Q: Use the method of mesh-current analysis to find the branch currents indicated in the network

A: The given circuit is as shown below,

Q: Q.2 For the circuitshown in Figure below, find the value of unknown currents by using mesh analysis.…

Q: If the mesh current 12 = 0.827117.17° A, the supply curent l=1.2L45° A, and R=2.2 0, for the…

A: To find the power factor of current source in the given circuit

Q: what is the impedance of the neutral line

A: Balanced 3 phase supply is applied to the balanced output It is asked to find impedance of neutral…

Q: Determine the total power information for a three parallel connected loads: LOAD 1: 250 VA, pf =0.50…

Q: 5mH 500 www m ~6V.COs (20T-1000+) {1k Luf reepeer 100mH

Q: Find the unknown currents in figure below Assume X -20 A Y=19 A Z -16 A. YA 5A I: + ZA XA 3A3 In

A: The given circuit is, X=20 AY=19 AZ=16 A

Q: Calculate the total resistance, the inductive reactance, and Impedance of the RL parallel circuit

A: In this question we will find total resistance, inductive reactance , impedance of given circuit....

Q: The load consists of everything to the right of nodes a and b. What is the power factor of the load?…

Q: Three resistors each of 31 Ohms are connected in DELTA connection to a 408 V, 50 Hz supply. Choose…

A: Three resistors each of 31 Ohms are connected in DELTA connection to a 408 V, 50 Hz supply. For…

Q: 3 5 How many degrees out of phase are the current and voltage in Question 2? 6 Refer to the formulas…

Q: Find equivalent impedance of below circuit.

A: It is given that:

Q: Given a parallel circuit shown below, determine the: a. Branch current b. Total current c. Total…

Q: ine the maximunn power transfer to the load resistor RL. lokN 4ar 22KN wr 十 Vo 6o RL 50ル 9on定 o003…

Q: R XL Xc · 아

Q: For the circuit in the figure, Vab = 440 V20°. Find the phase and line currents. -20 11, Ve 20 f EAN…

Q: Determine the power factor of the source. R = 6 Ohms

A: The given circuit diagram is shown below,Here, the value of R is 6 ohms.So,

Q: In three phase power measurement, current coil is connected in series and potential coil is…

A: In three phase power measurement (wattmeter) consists of a current coil connected in series with…

Q: Define the terms microprocessor, microcomputer, and microcontroller.

A: Microprocessor It is a small-scale electronic device. It is used in the computer to do the…

Q: Find the Value of the impedance only using Ohm law, Kirchhoff Current and Voltage Law and Voltage…

A: In this question we need to find the Value of the impedance ( Z ) shown in the circuit

Q: 3. Three impedance of 3-j42 are connected in delta across a 400V,50HZ 30 AC supply. Find all the…

Q: The load consists of everything to the right of nodes a and b. What is the power factor of the load?…

A: According to question we have to calculate the power factor of load with the help of given circuit.

Q: From the following circuit, determine the load impedance ?? necessary to ensure that the load…

A: In this question, We need to determine the impedance ZL for the maximum power transfer? Maximum…

Q: Draw resoltent Phaser Dragram indicationg the supply voltege and curent When 26.8V/50H2isupply…

Q: A voltage and current applied to a single phase load is v= 25 sin (300t+30) and i= 18 sin (250t-…

A: According to question we have to find, Phase angle, active power, reactive power.

Q: Ex2 R finel power Re5o JORDAN - AMMAN Tz Z

Q: For the given measured voltage and current, what is the impedance Z?

A: impedance is the ratio of the voltage to the value of the current.

Q: For the circuit in the following figure, find the circuit External Norton equivalent to load…

A: In the question to calculate the Norton equivalent at the load we have to to short circuit the load…

Q: Using Kirchhoff's Laws, calculate the current flowing through each branch of the shown. 6+j8 4.47…

A: In this question we will find currents in each branch......

Q: Determine the PHASOR values of V2 for the same circuit. 42 Vị 20/60° V V2 ww 15/0° V J4 Ω -j1Q

Q: 15. Find the Line and Phase Currents of the Circuit R1 L4 0.5mH R5 50 R6 V4 L1 L2 R2 L5 R4 30μH L3…

A: Given: Consider the following circuit: To find: The line and phase currents of the circuit.

Q: Consider the bistable circuit below left with the positive input terminal of the op-amp connected to…

A: (a) The operational amplifier's positive-input terminal is connected to a positive voltage source V…

Q: In three phase power measurement using star connected system, reactive power can be calculated…

A: In star connection Line voltage Vph = VL (line voltage )/ √3 Line current IL = phase current Iph

Q: Use Mesh Analysis to get the current of each load. I, j60 2 20 Ω 80 Ω ww 100/120° V -j40 Q -j40 Q 60…

A: According to the question we have to find the current in each load.

Question

360 kVA
estion
840 kVA
630 KVA
O 480 kVA
What are the phase current and phase voltage in a star connected load when this load connected to a delta power
supply has a phase voltage 1100 V and a phase current of 37 A
O 64 A, 1100 V
32 A, 635 V
64 A, 635 V
O 32 A, 1100 V
The unit of Wb / m² represents the
O magnetic field
ENC
Magnetic induction
US

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What are the resistance readings?
QUESTION 12 For the following two phasors: V=202-48° I= 102-19° What is the phase angle in degree by which the voltage leads the current?
Draw power triangle of circuitDraw the phasor diagram of the circuit
In a series circuit of R = 5 ohms and L = 0.03H the current lags the applied by 80 deg. What is the complex impedance?
Help!
She plant eapacity of a 8-Phage Senerating 10,00 KVA station cansist of generators ot and two Yeactence 12%. each S000Kvn Senerautor ot Reactace one 18% The Semerator bus-bar fr6 m are connectud to The station which Load is taken through Three step -up Trans formmegs houning Reacience of S%%. Determine Fault MyA 500 kVA the mayimmum The ciNcut. which breaker on I. Low voltaje side and Hrsh Voltage side may have to deal with.
500 N 1000 N 160 nF 100 mH R = 500 A, R3 = 1000 N, L = 100 mH,C = 160 nF,i,(t) = 4 cos 5000t mA %3D %3D i,(t) = 4 cos 5000t mA Sinusoidal current sSource Voltage on sinusoidal current source Voltage on capacitor Current passing through the capacitor Inductance voltage, Current flowing from inductance Voltage over resistance R, = 500 N R2 = voltage over 1000 resistors Vct) ic(t) VR, (t) VR,(t) ia) a-4 mAR ta) O--4 VAR Which of the following is the reactive power on the current souroe? d) --U mVAR e) Q- 12 MVAR 1) Q- 12 mVAR
Use superposition to find the indicated branch currents.
In star connection three phase reactive power is ?
Determine the current and the voltage across each resistor. Answers: 10 A, 7.5 A, 2.5 A, 50 V, 30 V.
The values of the circuit elements are given below.Accordingly, what is the maximum power transfer that can be made to ZL? V=11.7 phase 30 VR=12 ohmsL=j20 ohmsC1=-j14 ohmsC2=-j8 ohms
For an AC source of 0.39V calculate node voltage V