What are the general sources of error when using Vernier Caliper? when using Micrometer Caliper?

Q: Angle plate is a marking instrument used in workshops used to support workpieces during marking and…

A: Angle plate is a marking instrument used in workshops used to support workpieces during marking…

Q: Q.6) Complete the following table: No. Part of vernier calliper 1 Main Scale Vernier Scale 3 Screw

A: The main scale reading is that to the left of the zero on the vernier scale. The vernier reading…

Q: Explain the Repeatability and Reproducibility of Vernier Caliper with a sample and Example.

A: Measurement is very important process and if there is any error in the instrument or measuring…

Q: Make a representation of the layout of the Cartridge, the nomenclature and the scale on an A4 format…

A: It is asked to provide a representation of layout of the catridge

Q: What is the definition of temperature?

A: Given question: What is the definition of temperature?     Given question is related to…

Q: describe the operation of electro-mechanical parking brake.

A: Electro-mechanical parking brake An electromechanical parking brake is a type of parking brake that…

Q: What is angular indexing and block indexing?

A: Angular indexing:  It is similar to simple indexing except that in this process, instead of rotating…

Q: * The number 8 is pointed to 10 brake drum. brake pad lining. brake caliper piston. brake caliper.…

A: The number 8 is pointed to brake shoe lining.

Q: Air flows through a 10- inside diameter tube, at an average temperature condition of 300'F. The…

A:

Q: Draw and Label the part of Vernier and Micrometer Calipers. Provide a brief description of each part…

A: In this problem, it is asking for the diagrams of Vernier Caliper and Micrometer.

Q: It is common practice to assign a larger portion of the location tolerance to the hole.

A: Fill in the blanks.

Q: Technician A says that a micrometer can be used tomeasure the outside diameter of something.…

A: Micrometers exist in a variety of forms, depending on what they're used for. An exterior…

Q: A

A: Given : The tolerance off hole = 0.5

Q: The depth measurement is done by ___________________part of a Vernier Caliper. Ratchet Anvil Spindle…

A:

Q: A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a…

A:

Q: 5 ft 2 ft 7 ft The train has a weight of 23000 Ib and a center of gravity at G. It is suspended from…

A: Free Body Diagram for the given condition can be made as shown below: All normal reactions are…

Q: Describe two scales in Vernier Caliper?

A: Vernier caliper instrument is mainly used for taking accurate linear measurements. Vernier caliper…

Q: Triangular files are commonly used for filing corners between 60° and 90° Select one: O True O False

A: Triangular files were initially made for trimming saw tooths and gear tooths as the triangular cross…

Q: among the ruler and vernier caliper gave the least % err

A: Ruler and vernier caliper both are measuring devices.

Q: Slip gauges are standards used along with sine bar for direct angular measurement of workpieces in…

A: Slip gauges are standardize pieces of metal with specific size to a greater degree of accuracy. they…

Q: Refer to the 1.914 dimension. B) What is its tolerance ? ________________________________ C) What…

A: Tolerance for the given dimension is 0.01. now as tolerance = upper limit - lower limit. and we also…

Q: Compare the resolutions and accuracies of ruler, micrometer and vernier caliper

A: Measurements Devices : Ruler : Ruler is measuring device which is marked with units on its edge for…

Q: how to position this locator on a plate base for a part to ensure conformance with the Production…

A:

Q: 1st image : What is the reading on the micrometer? 2nd image : What is the reading on the…

A:

Q: skating is an example of _____________ . Select one: Rolling friction rotating friction sliding…

A:

Q: What is the meaning of dead weight in case of dead weight tester?

A: A deadweight tester is a calibration standard that uses the pressure balance concept to calibrate…

Q: 6. This is in a form of box wherein the needed data for dimensioning is placed. _ 7. AISI steel…

A:

Q: What component does a tubular inside micrometer include that allows it to measure a wide range of…

A: Adjustable anvil is the correct answer.

Q: Describe the procedure for using compressed air to remove a piston from a brake caliper.

A: Sometimes piston sticks in the bore in a disk brake.

Q: Neither A nor B is correct

A: Solution ,

Q: Connecting rod bearings are to be replaced. The journal measures 70.866 mm (2.790 in.)​. The…

A: The Size bearings for above requirements are U/S--0.381 mm (0.015 in) undersize.

Q: The primary manufacturing process for the rocker arm is stamping. True False

A:

Q: What is the cause of slipping inductile failure?

A: Causes of slipping in ductile failure are as follows

Q: What is the reading on the caliper dial? 90 10 80 20 sj6/7|8|9|2|1|2|31| -70 001 30 60 40 50

A: Given, Smallest reading on main scale = 0.1 unit Total number of divisions on dial = 100 Hence,…

Q: How are micrometers and vernier calipers checked for calibration?

A: Micrometers and vernier calipers. Both the devices are known for their precise measurements…

Q: What is the caliper reading on the diagram that is attached?

A: Given that Dial calipers We know that Dimension = Blade reading + dial reading Blade reading = 2.4…

Q: words to explain How to calculate the total reading of the Vernier Caliper in a simple way

A: Given:

Q: Apply geometrical tolerance to the below machine part in which the surface must be contained between…

A:

Q: List three rules to follow when using or storing semi-precision measuring tools.

A: Semi precision tools are used for the measurement of the various dimensions of the workpiece.

Q: What is the difference between floating and slidingcalipers

A: In the braking system, both floating and sliding calipers are used as per the requirement of the…