Can you answer the question? What additional complication would we need to consider when working with semiconductors in this wavelength range that wouldn't be a factor if we were working in thevisible range?A. Choosing between CCD and CMOS arrays.B. Need to mitigate atmospheric turbulenceC. Need to cool the detector to reduce noiseD. Large semiconductor bandgap causes the Boltzmann effect

CCD : stands for charge coupled device. It is an integrated circuit etched onto a silicon surface…

What additional complication would we need to consider when working with semiconductors in this wavelength range that wouldn't be a factor if we were working in the visible range? O A. Choosing between CCD and CMOS arrays. O B. Need to mitigate atmospheric turbulence O C. Need to cool the detector to reduce noise O D. Large semiconductor bandgap causes the Boltzmann effect

What additional complication would we need to consider when working with semiconductors in this wavelength range that wouldn't be a factor if we were working in the visible range? O A. Choosing between CCD and CMOS arrays. O B. Need to mitigate atmospheric turbulence O C. Need to cool the detector to reduce noise O D. Large semiconductor bandgap causes the Boltzmann effect

Principles of Information Systems (MindTap Course List)

12th Edition

ISBN:9781285867168

Author:Ralph Stair, George Reynolds

Publisher:Ralph Stair, George Reynolds

Chapter3: Hardware: Input, Processing, Output, And Storage Devices

Section: Chapter Questions

Problem 8DQ

See similar textbooks

Similar questions

....
Copper interconnections are introduced into state-of-the-art ICsbecause of its lower resistivity of r = 1.66µW.cm. If thisinterconnection line runs diagonally from one corner to the othercorner of a 20mm X 20mm silicon integrated die, what is theresistance of the line of 1µm thick and 10µm wide?
write about hertz (Hz) ?
you should first design a signal conditioning device and calculate the corresponding values and then do simulations for the designed circuit to verify your answers. (You can use any circuit design software that you prefer). Please include your circuit schematic and related input-output figures for your simulation. Assume that for a given accelerometer sensor the measured output voltage is 15 mV /g. (g is the acceleration expressed with respect to the Earth gravity i.e., 1 g = 9.8 m/g2) For this accelerometer design a suitable signal conditioning device capable of generating an output voltage of 0.27 V for each velocity unit m/s. For your design calculate the required gain of the device and determine the ratio of the resistances in the feed back. Draw your designed signal conditioning device in any circuit design software that you prefer and verify your design. Please include your system's schematic circuit and the resulting input-output figures in your answer sheet. I. I.
write python program which solve this problem; Consider a conductive bar with k = 5 and a length of 20 cm. Assume that one end is on the origin and the bar is located along the x-axis. Also assume that the charge density is 4 C/cm at point x=5cm and charge density -4 C/cm in the center of the bar and -4 c/cm at point x=15cm. If we assume that the two ends of the rod are quesi-potential and have a contract potential are 10 volts, calculate the amount of potential along the rod and at distances of 5.2 mm from each other using the method Jacobie and Gauss-Zeidel) notw: Suppose you work in all units &.= l 0/10
A parallel plate capacitor has an area A = 4.0 x 10-4 m2 and a plate separation d = 1 mm. Its capacitance C is Hint: space permittivity ɛ, 8.85 x 10-12 C2/N. m2 a) 3.54 x 10-12 F b) 5.31 x 10-12 F c) 4.72 x 10-12 F d) 3.98 x 10-12 F e) 4.13 х 10-12F f) 1.77 x 10-12 E. O a e O d
4- The data sheet of a quad two-input NAND gate specifies the following parameters: IoH (max.)=0.4 mA, VOH (min.) =2.7 V, VIH (min.) =2V, VIL (max.)=0.8 V, VOL (max.)=0.4 V, IOL (max.)=8 mA, IL (max.)=0.4 mA, IH (max.)=20µA, ICCH (max.)=1.6 mA, ICCL (max.)=4.4 mA, tpLH =tpHL=15 ns and a supply voltage range of 5 V. Determine (a) The average power dissipation of a single NAND gate, (b) The maximum average propagation delay of a single gate, (c) The HIGH-state noise margin and (d) the LOW-state noise margin
Task: DL34. In digital electronics, a NAND gate (NOT-AND) is a logic gate which produces an output which is false only if all its inputs are true; thus, its output is complement to that of an AND gate. A LOW (0) output results only if all the inputs to the gate are HIGH (1); if any input is LOw (0), a HIGH (1) output results. A NAND gate is made using transistors and junction diodes. Minimum number of NAND gates required to implement the following binary equation (A'+B') (C+D)?
Write the short answer for the following: (a) What is "Seebeck Effect"? Explain (b) Explain how capacitive type of transducers can be used for pressure measurement. (c) What are the different factors which influence the choice of method used for the measurement of flow? (d) Explain briefly how small displacements can be measured by a linear or differential transformer. (e) Explain the factors which influence the response of a temperature sensing device.
Calculate the logic swing, transition width, and the midpoint voltage for an depletion loaded - NMOS inverter. Use VDD= 15 V, VTo= 1.3 V, VTL = _3.2 V, (W/L)o = (20/5), and (W/L)L = (10/10). Use k' = 20µ for %3D both transistors? Answer (Vm = 2.8, LS = 14.92, TW = 1.010)
Consider the following quantum information circuit. Assume that error(X) happens on the second qubit. Show that t=how it will propagate through the given diagram at each step from t= 1 to t = 6. Explain in detail. 1 2 3 4 5 6 X H
Define Moore's law.