We want to create a converging nozzle. The nozzle will be connected to a shop compressed air system through a tank. The requirement for the nozzle inlet area is A₁ = 20 cm² and the requirement for the nozzle exit area is A₂ = 5 cm². We want to find the air tank pressure, inlet Mach number, and standard volume flow rate for the different exit Mach numbers listed below: (Assume air inside tank has negligible velocity, temperature of the air inside the tank is 288 Kelvin, the nozzle exhausts to standard conditions P = 101 kilopascals): (a) M₂ = 0.3 (b) Me = 0.5 (c) M₂ = 1.0 Note: the standard volume flow rate (Q = m/p) assumes the density of the air is standard with p = 1.23kg/m³

We want to create a converging nozzle. The nozzle will be connected to a shop compressed air system through a tank. The requirement for the nozzle inlet area is A₁ = 20 cm² and the requirement for the nozzle exit area is A₂ = 5 cm². We want to find the air tank pressure, inlet Mach number, and standard volume flow rate for the different exit Mach numbers listed below: (Assume air inside tank has negligible velocity, temperature of the air inside the tank is 288 Kelvin, the nozzle exhausts to standard conditions P = 101 kilopascals): (a) M₂ = 0.3 (b) Me = 0.5 (c) M₂ = 1.0 Note: the standard volume flow rate (Q = m/p) assumes the density of the air is standard with p = 1.23kg/m³

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Consider steady, isentropic flow of air through a duct with varying area. At section 1, p1 abs), T1…

Q: A projectile travels at a speed of 260 m/s in air where the temperature is -10 °C. Find the Mach…

A: Mach number is defined as the ratio of inertia force to the surface tension force. It is mostly used…

Q: What would you have to do to reduce this flow angle to zero degrees?

A: Here the reducing flow by zero degree angle attack

Q: The reservoir pressure of a supersonic wind tunnel is 5 atm. A static pressure probe is moved along…

A: Given:- Pressure=5 atm To find:- To find local mesh number and area ratio at a) 4 atm b) 2.64 atm c)…

Q: At a given point in the high-speed flow over an airplane wing, the local Mach number, pressure, and…

A: Solution: Given Data: M = 0.7 P = 0.9 atm T = 250 K

Q: An aircraft cruising at 1000-m elevation, z, above you moves past in a flyby. It is moving with a…

Q: i. Find the Mach no. of an aircraft flies with the same Mach no. at elevations of 8000m (T=-42 C°)…

Q: The Mach no. of a fixed geometry inlet at overspeeded for starting mode (Ai= 0.13 m2, At= 0.095 m2

A: Inlet Area, Ai = 0.13 m2 Throat Area, At = 0.095 m2

Q: 3. The NASA X-43 flies at a Mach number of 9.4 at an altitude of 30,000 m, where thepressure is…

A: a. V=2832.61sm,T0=4219.872K,P0=32962kPab. vs=1303.87m/s, T0s=77941K, P0s=3392510kPac.…

Q: Problem 1: The inlet of a jet engine flying at supersonic speed (M∞ > 1) is supposed to compress…

A: Given data:Inlet area = AiThroat area = A*Area ratio= 1.3and, throat is always sonicThe objective of…

Q: b) Air flowing at a velocity of 'X' km/hr has a static pressure of 'P' kN/m² and a temperature of…

Q: a) A convergent nozzle with a given area ratio is supplied with air at a constant stagnation…

Q: 4. A converging-diverging nozzle is designed for Mach Number, M = 2.0 at the exit. Air is supplied…

A: Given mech number at exit (me) = 2 Given pressure (P1)=900kpa Given temperature (T1)=500 k

Q: The mass flow rate of a calorically perfect gas (Cp = constant) through a Convergent-Divergent…

A: In order to determine the mass flow rate through a converging diverging nozzle, we must first take…

Q: Consider the supersonic flow over a 5° half-angle wedge at zero angle of attack, as sketched in…

Q: A flow with Mach number M1 = 2 and pressure p1 = 1 atm is turned away from itself twice, first…

A: The diagram for first flow with two turns,

Q: Methane is flowing through an insulated 15-cm diameter pipe. The entering conditions are kPa, 100°C,…

A: Given data,d=15cmf=0.023P1=600kpaT1=100°Cm=5kgs

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Answer

Problem Statement

Solution

b) Me = 0.5

c) Me = 1

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Air flows through a constant-area, insulated duct. At location 1, the conditions are Maj = 0.4, T1 = 60°C, p1 = 200 kPa (abs). Downstream, at location 2, Maz = 0.8. Assume steady flow and ideal gas with constant specific heats. Determine: a. stagnation temperatures, To, and Toz [K, °C] b. velocities, Vị and V2 [m/s] c. stagnation pressures, po, and poz [kPa] d. entropy change, s2 – s1 (kJ/kg K] e. show static and stagnation states and process on T- - s diagram
For Air: y = 1.4 PART B Question B1 a) With the aid of sketches give a clear account of the operation of convergent nozzles as a function of back pressure. In your answer clearly indicate the critical points (pressure ratios) along the pressure ratio axis. b) Determine the required area ratio A part of the expansion of new teaching and research facilities at QMUL, a new two dimensional blow- down supersonic jet facility is going to be designed, manufactured and installed at our Whitehead Aeronautical Laboratory, Figure QB1. The design Mach number for this facility is M₁ = 2.0. A = A₁ A R=287J/kg K A₁ location at which the area ratio ( A₁ c) What should be the supply pressure to the nozzle (P) in order to have a normal shock wave at a Ax =) is 1.5? A Settling Chamber Po To for this design Mach number. d) For part c, what would be the discharge mass flow rate per unit throat area? You may assume P =105 N/m² and To = 300K. atm Convergent-Divergent Nozzle A AX Schematic of a Supersonic Jet…
The convergent-divergent nozzle in Figure 22 expands and accelerates dry air to supersonic speeds at the outlet, where p2 = 8kPa and T2 = 240K. At the throat p1 = 284 kPa, T1 = 665 K and V1 = 517 m / s. Assuming steady and compressible flow of an ideal gas, estimate (a) the mass flow wn kilograms per hour, (b) the velocity V2, and (c) the match number Ma2
Determine the force in each cable used to support the 50 lb. crate.
I need the answer quickly
What is the Mach number of an airflow with a velocity of 2000m/s, at 2,000 ft altitude?
01: The velocity, pressure, and temperature at a certain point in a steady air flow, are 600 m/s, 70 kPa, and 5 °C, respectively. If the pressure at some other point in the flow is 30 kPa, find the Mach number, temperature, and velocity that exist at this second point. Assume that the flow is isentropic and one-dimensional.
On October 3, 1967, pilot William J. "Pete" Knight set a world record that still stands to this day for the fastest flight by a crewed, powered aircraft by flying the North American Aviation X-15 as fast as Mach 6.7 at an altitude of 102,000 ft above sea level. Mach number is the ratio of an object’s velocity to the local speed of sound. Using the table for atmospheric properties with respect to altitude, calculate the speed of sound at an altitude of 100,000 ft. What must have been the velocity of the X-15?
b) In a converging-diverging duct the flow conditions are such that a normal shock is formed at the exit of the diverging section. Upstream of the shock the flow conditions are as below. Mach number= '5.198', Pressure= '311886.9' Pa and Temperature= '228.72' K. Obtain the Mach number, pressure, and temperature at the downstream of the shock. Assume standard air properties (y=1.4).
2. The total temperature and total pressure (absolute) in the reservoir of a converging-diverging high-speed wind tunnel are 500K and 3x10 Pa, respectively. The throat area is 25 cm² and the Mach number in the test section is 3.0. Find the test section area in cm2, mass flowrate in kg/s, pressure in Pa, temperature in K, and air speed in m/s in the test section.
Question 3: a) In a '72.77' mm diameter pipeline conveying air, the inlet Mach number is measured to be $0.5198'. Find the length of the pipeline at which the flow conditions become sonic. Assume standard air properties and the average friction factor obtained from independent tests is 0.02. Also obtain Mach number at 1 m from the inlet of the pipe.
5. For the subsonic axial-flow air expander specified, calculate the stagnation and static pressures and temperatures and the Mach number at the rotor-inlet plane (figure P2.5). Also find the rotor rotational speed and the nozzle-inlet blade height for constant-outer-diameter blading. Sketch the form of the complete turbine expansion on an enthalpy-entropy chart. The axial velocity will be constant at this design point. Mass flow, m = 2 kg/s Nozzle-inlet stagnation temperature, Tuni = 400 °C. Absolute nozzle-inlet stagnation pressure, Po,ni = 3 bars(= 3 x 105 N/m²) Mean diameter, dm = 0.25 m. Blade height at rotor entry, 1 = 0.1dm(= 1/2[ds - dn]). Flow angle at nozzle exit, a₁ = 70° to axial direction. Drop in stagnation pressure in nozzle, Apo = 0.05 bar Rotor peripheral speed at mean diameter, um = 0.5x (component of nozzle outlet velocity, Ce,1).