We use the DFT to compute the amplitude spectrum of a sampled data sequence with a sampling rate fs =2,000HZ. It requires the frequency resolution to be less than 0.5 Hz. determine the number of data points used by the FFT algorithm and actual frequency resolution in Hz, assuming that the data samples are available for selecting the number of data points.

We use the DFT to compute the amplitude spectrum of a sampled data sequence with a sampling rate fs =2,000HZ. It requires the frequency resolution to be less than 0.5 Hz. determine the number of data points used by the FFT algorithm and actual frequency resolution in Hz, assuming that the data samples are available for selecting the number of data points.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. The CT signal x(1)-6cos (800zt) + 8cos² (mæt) is eritically sampled (Nyquist rate) by f-8000 Hz. Find: i. The value of m. ii. The frequency components of the signal. The frequency resolution (A) of the output spectrum if the sampled signal is processed by 32point-DFT. iii. iv. Define frequency resolution.
Digital signal process subject , need quick amd correctly
5 a) Consider the sample sequence (5000, 5000, 5000, 5000, -5000, -5000, -5000, -5000}. These are samples of a square wave with a period of eight samples or 1ms at 16 KHz sampling frequency. What are the sinusoidal frequencies in the output waveform?
PROBLEM A transformer has 600 primary turns connected to a 1.5 kV supply. Determine the number of secondary turns for a 240V output voltage, assuming no losses.
What is a minimum number of sampling frequency required to have distortion free reconstruction of a digital signal from its samples?
A central station is setup up for simultaneous monitoring of 10 hospital patients. The data from the 10 patients are brought to a processing center over wires and are sampled, quantized, binary-coded, and time-division-multiplexed. The multiplexed data are transmitted to the monitoring station as shown in the figure below. The bandwidth of the signal received from each patient is 200 Hz. The maximum acceptable error in sample amplitudes is 0.5% of the peak signal amplitude. The sampling rate must be at least twice the Nyquist rate. Determine the sampling rate, the number of levels, the number of bits per level and minimum cable bandwidth needed to transmit the data. Processing center Cable Receiver (14)
Q. Suppose that you have an angle modulaton system with an input signal £01) s wiangle wave of fundamental frequency 5 kiz and its most power is concentrated in the frst third harmonics, the masimum and minimu voltage ae | and -1 espectively. where one period equation of theinput s o[BIl 0
digital signal prossesing
3. Define aliasing, and suggest the methods to avoid aliasing problem. The spectrum of selected CT signal is given below. Draw the spectrum of the sampled signal with critical sampling, under sampling by 20%, and oversampling by 50%. Discuss the result. 10 -100 100 f (kHz)
11. A 1550-nm single-mode digital fiber optic link needs to operate at 622 Mb/s over 80 km without amplifiers. A single-mode InGaAsP laser launches an average optical power of 13 dBm into the fiber. The fiber has a loss of 0.35 dB/km, and there is a splice with a loss of 0.1 dB every kilometer. The coupling loss at the receiver is 0.5 dB, and the receiver uses an InGaAs APD with a sensitivity of –39 dBm. Excess-noise penalties are predicted to be 1.5 dB. Set up an optical power budget for this link and find the system margin. What is the system margin at 2.5 Gb/s with an APD sensitivity of –31 dBm? Answer: 14.1 dB and 6.1 dB
Hi .. Please solution this question and required points . Thank you.
The Nyquist sampling interval, for the signal sinc(700t) + sinc(500t) is?