PárrafoEstilosWe can make use of a non-inverting amplifier to build acurrent source. To do this, consider the following circuit:RWhere one of the resistors that make up the configuration hasbeen replaced by a box black (charge). Show that the current iis independent of charge and is given by t, =V.RSuppose the amplifier is biased with ±15V and that the black boxis a resistor RL. IsV, = 2V and R 2.2k. ¿What is the range ofvalues of R for which this configuration works as currentsource?sibilidad: es necesario investigarSHOT ON POCO X3 NFC

Answered: Image /qna-images/answer/6f3c0622-b868-4819-b870-9b77add693c4.jpg

We can make use of a non-inverting amplifier to build a -current source. To do this, consider the following circuit: Where one of the resistors that make up the configuration has been replaced by a box black (charge). Show that the current i Ve is independent of charge and is given by i, = Suppose the amplifier is biased with +15V and that the black box is a resistor R1. IsV, = 2V and R = 2.2k. What is the range of values of R for which this configuration works as current source? ad: es necesario investigar 85 DOO SHOT ON POCO X3 NFC

We can make use of a non-inverting amplifier to build a -current source. To do this, consider the following circuit: Where one of the resistors that make up the configuration has been replaced by a box black (charge). Show that the current i Ve is independent of charge and is given by i, = Suppose the amplifier is biased with +15V and that the black box is a resistor R1. IsV, = 2V and R = 2.2k. What is the range of values of R for which this configuration works as current source? ad: es necesario investigar 85 DOO SHOT ON POCO X3 NFC

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Label properly the required final circuit and DC loadline. Complete the given BJT circuit. Solve for the value of the resistors and voltage supply that will satisfy the given loadline
What are circuits can used to design Class B amplifier ? explain the important features ? for each
give short answer in 10 minutes i will give positive feeback
Do b)?
Hand Calculation: Since you now have the values of R1 and R2 resistors, obtain numeric value of voltage gain Av=Vo/Vi, and numerical values of input and output resistances Ri and Ro. Note that you need to DC analysis first. Do a hand calculation and calculate the DC collector current or IC. This is needed in order to calculate the small signal parameters gm and rπ and in turn to obtain the Av , Ri and Ro Hence, first perform a DC analysis (use the circuit in Figure 1 and take all capacitors open) and assume your transistor has a β=140.
give short answer in 15 minutes i will give positive feeback
Four voltage sources of 3 V, 4V, 2V and 3V respectively are to be applied to the input terminal/terminals of “an" inverting amplifier. Design two different circuits for the two different cases with justified explanation and selection of proper resistances as per the requirements below: a) When an output of 4V is required (with phase shift). b) When an output of 8V is required (without phase shift) Note: Only inverting amplifier/amplifiers to be used for each case and all the voltage sources are to be used for each individual design as required in a) and b). 2.
Please solve with steps, using to study. Will upvote!
Note : Value of K1 = 17; K2 = 49 Show the each equation part and Mention ans same as asking in question. There are must be 2 graphs. Read the 2 pictures clearly and ans all the question. For Example : "Compare T+,T- , Draw the transfer characteristics V0 and V1 " Mention like this then ase the question. formula should be taken from "Operational Amplifier and Linear Integrated Circuits, by Robert F. Coughlin and Fredrick F. Driscoll, 6th Edition, Pearson." this book.
1. Calculate the following items related to practical op-amp circuit applications. a.) If the inverting amplifier circuit has R1 = 50 kN and R, = 370 kn, what output voltage results from an input of V, = 5v? b.) If the circuit has R1 = 75 kn and R, = 180 kN, what output voltage results from an input of V, = -1.7v? c.) Calculate the output voltage of a noninverting amplifier given the following values: V, 5v, Rf = 140 kN, and R1 %3D = 80 kN.
1. Discuss the difference between Passive and Active Components? Give examples
4) Below is the small signal model of a multistage amplifier. Using this model, write the equationsthat you would need to determine the voltagegain. IMPORTANT: You only need to providethe equations that you would need to determinethe voltage gain. You DO NOT need to combine and simplify the equationsto determine a final expression for the voltagegain. Vin Vo Vb vo1 Rb R13 Vbe1 Vbe2 'e gm 1 Vbe1 gm 2 Vbe2 Rc2 Rc1 Re