Water (SG=1) flows through the diverging frictionless pipe shown at flowrate of Q with the given parameters below (g=9.81 m/s?)Q=500 m³/h, P1=500 kPa, z1=3 m, Z2=14 m, D1=400 mm, D2= 500 mmThe inlet velocity ism/s (0.95;1.00;1.05;1.11;1.16)The exit velocity ism/s (0.61;0.64;0.67;0.71;0.74)The exit pressure iskPa (374;392;412;433;454)

Given data as per questionQ=500 m3h=0.1388 m3sP1=500Kpaz1=3mz2=14mD1=400 mmD2=500 mmwe know…

Answered: Water (SG=1) flows through the…

Water (SG=1) flows through the diverging frictionless pipe shown at flowrate of Q with the given parameters below (g=9.81 m/s?) Q=500 m3/h, P1=500 kPa, z1=3 m, z2=14 m, D1=400 mm, D2= 500 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle diameter (75mm) and pipe length from (1 to 2) was (100m) Determine the length of pipe from (2 to 3), and the pressure at point (2). (e-0.026mm, v1.13" 10 m?/sec). Fig(1) 6m 23m Fig.(1) Nozzle
Q20/ The pipe flow shown in the Fig. is driven by pressurized air in the tank. What gage pressure P₁ is needed to provide a flow rate of 50 m³/hr. Neglect minor losses. 3600 Smooth pipe: d = 50mm Pl I 10 m 40m 20m 80 m Open jet
The figure shown below is a series pipeline system used to draw a fluid from a lower source open tank to a higher destination open tank . The flow and geometric layout for the system are listed below: Fluid: water Volume flow rate: Q=0.015 m3/s Elevation difference: h=8.0m of two free surfaces Suction line: DN100 Sch. 40 Steel pipe Length: Ls=2.0 m Valve1: hinged disc type foot valve Entrance type: well-rounded Discharge line: DN80 Sch. 40 Steel pipe Length: Ld=100 m Valve2: full open gate valve Elbows: 90ο long radius elbow (1) Select the simplified general energy equations for section 1 and 2_________ A. B. C. D.
1) Determine the Pressure and Velocity head at each point. Find the exiting flowrate. Point 1 2 3 4 5 6 Kent=1 Pressure Head Pipe 1 Kbend-0.2 Kexp=0.3 Velocity Head Kval=2.2 Elevation Head 70 62 50 48 45 43 4 Kbend-0.2 Kcont=0.1 Pipe 1 2 3 4 5 6 Kexit=1 Lm 250 150 150 170 100 200 D mm 150 150 300 300 300 150 f 0.022 0.022 0.02 0.02 0.02 0.022
Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.Water flows through a schedule-40 pipe that changes gradually in diameter from 6 in (154mm) at point A to 18 in (429 mm) at point B. The volumetric flow rate is 5.0 *3/sec (130 L/s). The respecLve pressures at points A and B are 10 psia (70 kPa) and 7 psia (48.3 kPa). All lossesare insignificant. What are the direcLon of flow and velocity at point A? (A) 3.2 */sec (1 m/s); from A to B(B) 25 */sec (7.0 m/s); from A to B(C) 3.2 */sec (1 m/s); from B to A(D) 25 */sec (7.5 m/s); from A to B
The pressure loss p in a pipe is related to the flow rate Q by the equation P = KQ^n, where K and n are constants. If K = 190 x 10³determine the value for n when a flow rate of Q = 0.04 m³/s causes a pressure loss of 180 Pascals.
The water is delivered with piping system given in the figure below. The levation difference between entering section and tank is 143,55 m. Estimate the gage pressure [MPa] at point 1. (Note: For water at 20°C, take p=998 kg/m and u=0.001 kg/ms. ) 5 cm diameter cast-iron pipe Length of the system is 1.2 km All fittings are flanged. The vohume flow rate is 300 L min 45 treaded elbow Yanit
Water flows from a 20-mm-diameter pipe with a flowrate Q as shown in the figure below. What is the approximate diameter of the water stream, d, in units of cm, if the distance below the faucet is, h=2 m, and Q = 0.003 m³ /s? 20 mm O a. 1.83 m b. 2.07 m O c. 3.29 m d. 4.66 m O e. 5.29 m
Water is stored in a tank sketched in the figure below to support the demand of a nearby community area.The system is designed so that pressure at the location B always lies in the range of 330 to 440 kPa (gauge).Water demand fluctuates between 0.3 and 1 m3/s regardless of pressure at B. The supply pipe of 600 mmdiameter and 1 km length between A and B is made of steel and has the equivalent sand roughness of 1 mm.Although not shown in the figure, the supply pipe has five 90◦ bends, each having the head loss coefficientof 0.8. The figure shows that the bottom end of the tank is located 42 m above the ground, and the pipe isburied 1.5 m below the ground. A pump system regulates so that the tank keeps the same water level all thetime. Assume water at 20◦C, and air in the storage tank has the atmospheric pressure. To meet the designcriterion for pressure at B, what should be the depth of water h in the storage tank?
A large tank is partly filled with oil (s.g.= 0.85), the air space above being under pressure. A 50 mm ϕ hose connected to the tank discharges on the roof of a building 15.25 m above the level in the tank. The friction loss is 5.50 m. What air pressure in KPa must be maintained in the tank to deliver 0.0124 m3/s on the roof?
4: Water flow through a pipe at 5L/s as shown in figure. If gage pressure of 12.5kPa, 11.5kPa and 10.3kPa are measured for P1, P2 and P3 respectively, what are the head losses between 1, 2, and 3? (2) -- 50 mm - 50 mm 10m O Pa d, - 30 mm
Water ( density 1000kg/m3) flows downward naturally through a vertical pipeline of diameter D=25 cm and length L= 100 m . Determine the pressure gradient causing flow ( USE π = 3 ; g = 10 m2/s ) ANSWER: 10 kPa/m (Although I wrote this is the answer under the question in some of the questions I posted before. Different answers were found from the answer. The exact answer to this question is 10kPa / m.)