Water is flowing vertically upwards through a pipeline having diameter 1m and 0.5m at the base and top,respectively. The pressure at the lower end is 450 mm of Hg, while the pressure at the upper end is 20kN per meter square. If the loss of head is 20% of difference in velocity head, Calculate the discharge. The difference in the elevation is 4m.

Q: A 4 inch Sched 40 steel pipe carries crude oil at 80°C. The crude oil has a dynamic viscosity of 1.2…

A: Given: 4 inch Schedule 40 steel pipe dynamic viscosity μ =1.2 x 10-2 Pa·s density ρ= 680 kg/m3

Q: PROBLEM 2.7 A mrolley that moves along a horizontal beam is actod upon by two forces as shown.…

A: Given: The vertical force = 2500 N = 2.5 KN Rx = 0 Ry = 2500 N

Q: Q2 // The diameter of a pipe at section 1 and 2 are 10 cm and 15 cm respectively. Given velocity of…

A: Given that, The diameter of the pipe at section 1 D1 = 10 cm = 0.1 m The diameter of the pipe at…

Q: Water is flowing in a conical vessel 15 cm deep and having a radius of 3.75 cm across the top. If…

A: Given Depth of conical vessel (H) = 15 cm Radius of top (R) = 3.75 cm Rate at which water…

Q: For a flow over a flat plate the normalized velocity profile is --² where y is in mm 2 U a)…

A: Answer: a) we know that, Displacement Thickness = δ* = ∫0δ (1- uU) dy  Displacement Thickness = δ* =…

Q: 5. A Pitot tube in the pipe in which air is flowing is connected to a manometer containing water as…

A: Given that- Manometer difference in water level, x=87.5 mm= 0.0875m Tube coefficient, CP=0.90…

Q: 1-Water with kinetic viscosity v-0.494 mm2/s flow through a pipe with diameter 18mm with velocity…

A: Kinetic viscosity = 0.494 mm2 /sdiameter = 18 mm V= 0.1 m/sf  = 0.03 mm

Q: Q3) Water flows through a 10-mm diameter pipe at a flow rate of 1.33×104 m³/s. Find (a) Velocity (V)…

A: As water is flowing through the pipe with a flow rate of Q. Reynold's number is the dimensionless…

Q: Water is flowing through a 30-m-long and 5-cm-diameter horizontal pipe at a rate of 9 L/s. Using…

A:

Q: mooth inner surface for

A:

Q: Water at 20°C is flowing through a tube of diameter 0.010 m at a velocity of 0.10 m/s. a. Calculate…

A: Water is flowing through the tube at 200C. Tube diameter, D=0.010 m velocity of the water through…

Q: Determine diameter of galvanized pipe needed to make the water flow along 180m with flow rate 85L/s…

A: Given data: Length of pipe = 180 m Volumetric flow rate = 85 L/s Head loss = 9 m Kinematic viscosity…

Q: The initial free fall of water from a faucet can be thought of as an inviscid flow because friction…

A: Given: The distance between points 1 and 2 is 7 cm i.e. z1 - z2 = 7 cm or 0.07 m The diameter of…

Q: horizontal duct of uniform

A: In fluid mechanics we study the behavior of fluid in three different scenarios which are fluid…

Q: 4. Water flows through a smooth horizontal 2 m long tube of 2 mm diameter with an average velocity…

A:

Q: 10 ft 10 ft Very large Water 3-in steel pipe FIGURE 6.25 Tank draining by gravity, with pipe and…

A: Water is flowing from the bottom of a tank via 3 in steel pipe. Volumetric flow rate is to be…

Q: Calculate the kinetic energy changes

A:

Q: Paddle agitator

A:

Q: Shear stress of the fluid will be maximum at the a. Wall of the pipe O b. In between center and wall…

A: 1) Answer: a. wall of the pipe Shear stress of the fluid is maximum at the wall because at the wall…

Q: 1. An incompressible fluid of kinematic viscosity v= p/p = 10-4 m²/s flows steadily through a…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: calculate the largest discharge for which the flow will be definitely laminar Water flows in a 2 cm…

A: This question is based on fluid mechanics. The flow in consideration is Laminar flow. Data given :…

Q: Sulphuric acid is flowing through a pipe (2.5 inch diameter, 50 ft length) in a velocity of 0.006 m3…

A: Given: diameter D = 2.5 inch = 0.0635 m, A = pi.D2/4 = 0.003165 m2 Thus, V = Q/A = 0.006/0.003165  =…

Q: Assume frictionless flow in a long, horizontal, conical pipe. The diameter is 2.54 cm at one end and…

A: (a) Let us assume the origin of coordinate axis along center of pipe. Hence there is no change in y…

Q: Water is flowing through a 2.067-in D pipe with a velocity of 1 m/s. Calculate: (a) Mass flowrate…

A:

Q: Consider the flow of a fluid through the piping system shown below in Figure 1.

A:

Q: 2.3 A 12mm diameter pipe 15m length is used to drain an oil tank. Determine the discharge when the…

A: given data:diameter=12mm=0.012mlength=5moil level in the tank 2m aboveh=2moil viscosityμ=0.01 pu…

Q: A crude oil with a density of 875 kilogram per cubic meter is pumped and flowing at 1.5 meter per…

A:

Q: The flow through a 1.0 in diameter pipe is 5 GPM with a pressure drop of 10 PSI. What would the…

A: Given: diameter of pipe 1(d1)= 1 in diameter of pipe 2(d2)= 2 in pressure drop in pipe 1 (∆P1)=10…

Q: Air is flowing through a horizontal tube with 1.00-in inside diameter. What is the maximum average…

A: Given data: Inner diameter of pipe = 1 in